Jump to content
LegacyGT.com

My 12.3 run


Recommended Posts

[ame=http://www.youtube.com/watch?v=1OEw9j-C0QI]Doogie's 12.3 @ 113 1.68 60' Subaru Legacy GT - YouTube[/ame]

 

MWSOC Subaru Shootout 2012

Vehicle Specifications:

2005 Legacy GT Limited Garnet Red Pearl

463 WHP E85

405 WHP Pump 93

Engine:

EJ255 2.5 Liter, Flat 4 Cylinder

NGK Iridium Plugs (1 Step Colder)

Crawford V2 Air/Oil Separator

Amsoil Synthetic 5W-30

Turbocharger & Induction:

Blouch 20G XT (8cm Hotside)

AVCS Kit with VF Series Banjo

Vibrant 90 Degree Elbow

STI Intake Manifold

Grimmspeed Phenolic Spacer 3mm

Grimmspeed TGV to Engine Gaskets

Grimmspeed Intake Manifold to TGV Gaskets

TGV Deletes

RacerX FMIC with Custom Fabricated Piping

Tial Q BOV 50mm 12 PSI Spring

HOA 3 Port Boost Control Solenoid

Samco Inlet Hose

Short Ram Intake

Fuel & Tuning:

Walbro 255lph Fuel Pump

Top Feed Injectors Conversion with Fuel Regulator

Custom Fuel Rails with Steel Braided Lines

Deatschwerks 1300cc Top Feed Injectors

Cobb Access Port 2.0 Tuned by Junior

Exhaust:

Perrin Equal Length Headers

Grimmspeed EWG Up Pipe

Tial MVS 38mm VTA EWG (.9 Bar)

Perrin Catted Downpipe

Magna Flow Resonator

Magna Flow 3" Y Pipe

Magna Flow Mufflers

Drivetrain:

2004 STI 6 Speed Transmission

Exedy Stage 2 Clutch Kit

Braided SS Clutch Line

Kartboy 6 Speed Short Throw Shifter

Kartboy Shifter Bushings

STI Front Axles

Spec B Rear Axles

R180 Rear Differential

Brakes:

2004 STI Brembo Calipers Front

DBA 4000 Slotted Rotors Front

Hawk HPS Pads Front

2004 STI Brembo Calipers Rear

DBA 4000 Slotted Rotors Rear

Hawk HPS Pads Rear

SS Braided Brake Line Set

ATE Super Blue Brake Fluid

Suspension, Wheels, & Tires:

Perrin 25mm Front Sway Bar

Rallitek Front Endlinks

BC Racing BR Series Coilovers

18x8 +50 Enkei Imola

Hankook Ventus V12 EVO K110 225/40ZR18

Interior:

52mm Auto Meter Sport Comp II Boost Gauge

52mm Auto Meter Sport Comp II Oil Pressure Gauge

Dual Stealth Cubby Gauge Pod

LED Conversion Kit (Dome, License, Door)

Recaro ProRide Blaze Carseat

Exterior:

R-Rev Front Lip Painted GRP

R-Rev V2 Eyelids Painted GRP

Blacked Out Grill

DDM Hid Headlights 6000K

Cleared and Blacked Out Headlights

White/Amber Switchback LED Turn Signal Bulbs

Rear Windows Tinted

Debadged Emblems

Link to comment
Share on other sites

  • Replies 89
  • Created
  • Last Reply
Thread Title: 1/4-1/8th: location of run, Vehicle, time/speed

example: 1/4 mile, NHIS, 2005 LGT, 13.6 @107mph

 

Event: track run

Loaction: name of the Track

Date: 08/11/2010

 

 

Ambient Temp: in F

Elevation: Google can help you with this

Weather: Rain? Snow? clear?

 

Car: year, make and model

Tuner: Name of person and shop

Track info:

Transmission: 5speed, 6speed, PPG, JDM, ect ect

Peak Horse Power at RPM: The RPM that you reached max HP

Peak Torque at RPM: The RPM you reached Max TQ

Fuel: Octane rating if pump, octane and brand if specialty fuel

Engine/Power Modifications: Anything that adds horsepower that you have added to your car. i.e. bigger turbo, intercooler, exhaust, injectors

Driveline Modifications: Stock/Upgraded clutch, light weight flywheel, upgraded drive shaft, upgraded rear or center diff.

Suspension Modifications: struts, springs, coilovers, braces, bushings, and other items that reduce body motion and increase power transfer to the ground

Other Modifications: weight removal, addition of a roll cage, lighter wheels or rotors, smaller than OE diameter tires, and other items that affect vehicle weight, rotational inertia, and power delivered to the contact patch

Picture of Dyno Plot and AFR/Boost Plot: Ask your tuner for this or copy it from your tuning software

Link to comment
Share on other sites

It was 90* that day. Do you think the trap should be higher? Comparing my power to other LGT's on dragtimes and other sites, my et and trap seems right to me. The 6mt adds some weight to the car. DANG, I knew I should have taken out the recaro baby seat!
Link to comment
Share on other sites

Interesting. You go through a whole lot of trouble doing a nice build and customizations, yet choose to use a racerX fmic. May I ask why?

 

I think the racerX fmic is a nice product. Keep the fogs, good size core, easy to install. The price to great. What fmic would you use instead?

Link to comment
Share on other sites

I think the racerX fmic is a nice product. Keep the fogs, good size core, easy to install. The price to great. What fmic would you use instead?

 

Nice compared to what? How many intercoolers have you had? Not ragging on you, but most people only like it because they haven't seen the nice stuff. You had to fab custom piping, i'm sure that wasn't done because you wanted to. There's a bunch of brands out there that are good. Avo allows you to keep your fogs and bumper beam as well. Most people shy away from the more expensive intercoolers. But this is one area where you get what you pay for. IMO, the racerX has one of the worst core densities that I have seen. While it may not be a knock off by definition, it shares the same quality as one. The biggest thing that I preach to people when it comes to intercoolers, is that not all cores are the same. Core density is just as important as size and location. I've had five different intercoolers and the Process west TMIC is the best one by far.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.




×
×
  • Create New...

Important Information

Terms of Use