Jump to content
LegacyGT.com

Perscitus' 2010 3.6R Build Thread


Recommended Posts

This is my first Subaru although I've followed the brand since the mid-90s and first starts of Imprezas in the WRC.

Carlos Sainz, Richard Burns, Alister and Colin McRae, years before a WRX existed as a model car.

 

Picked up my Legacy in the spring of 2010 and ever since, its been one wild ride. I love this car.

 

Engine, Intake & Exhaust

- Open-source EcuEdit/RomRaider/EcuFlash tune (~ 296bhp(221kW) / 362ft-lbf(490Nm))

- RAPTOR EZ36D SS Headers (2.25" ID)

- Custom Header-back Catless Mid-Pipe with SS Flex Coupler (2.5" ID)

- 2x VIBRANT GESI SS catalytic converters (2.5" ID, 400-cell, spun metal-core)

- 2x VIBRANT 18" SS Resonators (3" ID)

- MAGNAFLOW 16377 Catback Exhaust (3" ID)

(Raptor Header runner flange ID 2.25"-> 2.5" ID runners -> 2.5" ID Vibrant GESI Cats -> 2.5" ID pipes -> 3" Vibrant Resonators -> 3.0" ID Catback)

- KARTBOY Polyurethane 12mm Exhaust Hangers

- PRS Light weight crank pulley

- Continental Poly-V serpentine/accessory belt

- ATF Cooler (radiator bypass)

Suspension & Brakes

- RACECOMP ENGINEERING (RCE) Black Springs

- BILSTEIN Shocks

- OEM Group-N Top Hats (front and back)

- GTSPEC Front Strut Tower Brace

- GTSPEC Rear Strut Tower Brace

- OEM 2013+ 26mm Front Sway Bar

- WHITELINE BSR49XZ 22mm Rear Sway Bar

- SUPERPRO front/read end-links

- OEM TSB #05-48-10 parts (new steering column, dynamic damper weight,

lower steering control arms, bushings, revised steering rack spring seat, etc.)

- WHITELINE KCA414 Front Camber adjusting bolt kit

- SPC PERFORMANCE Rear LCAs with Camber Adjustment

- GOODRIDGE 24220 Stainless Steel brake lines

- HAWK Ceramic Brake pads

- STOPTECH Slotted rotors

- OEM Calipers painted flat black

- CUSCO Master Cylinder Brace

 

Exterior

- Black headlight housings by Lightwerkz

- BAYSON R S204 Front Lip (glossified)

- iJDMToy LED DRLs

- HELLA Supertone horns (wrinkle black) with SUBIMODs bracket

- Horn Harness (quad in-line with stock) by Lightwerkz

- 3M Smoked vinyl taillight housing overlays by Highline Detailing

- 3M Clear Bra Front and Rear Bumper by Highline Detailing

- 3M Ultra Performance Ceramic Series 35% Tint

- GLADMAN PERFORMANCE FABRICATION Rear Diffuser

- Semi-flat black vinyl wrapped door trim by Vigg Designs

- Semi-gloss black vinyl wrapped Subaru logo trims by Vigg Designs

- UNIONLUX 4500lm LED bulbs (low-beams, high-beams, fogs, position lights, DRLs, turn signals)

- TRS, MORIMOTO, VLEDs LED Lighting rear (quad-stop light mod, turn signals, license plate, reverse)

- BOSCH Latitude wiper blades

- Front License Plate relocated to just above front lip

 

Interior

- MYRON & DAVIS NAV Headunit (including 2018 maps)

- OBDLink MX and BtSSM Scan Tools

- BELTRONICS Vector 955 Radar Detector

- AUTOWINDOW Tap Turn Flasher Relay v4

- HEXIS Brushed Titanium Interior Accent Vinyl Wrap

- DAMD D-shaped Leather Steering wheel (silver stitching)

- OEM Pedal Covers + matching Dead Pedal

- OEM Leather Shift Knob

- OEM Tweeter kit

- OEM Cargo Nets

- REDLINE GOODs center console cover

- WEATHERTECH DigitalFit front and back mats

- WEATHERTECH DigitalFit trunk mat

- LED Lighting (courtesy, map, dome, trunk)

 

Wheels & Tires

- ENKEI TSP6 Hyper Silver (18x8.5 +45mm)

- MICHELIN Primacy MXM4 Grand Touring All-Seasons (245/45R18s)

- McGARD SplineDrive Lug Nut set (black)

 

Fluids

- Shell Rotella T6 5W40 or Motul 8100 XClean 5W40 or CASTROL Edge Titanium 5W30

- Nanotech Lubricants Auto Additve Plus

- Castrol Dexron VI Power Steering Fluid

- Amsoil ATF Fluid

- Amsoil Front and Rear Diff Fluid

- Amsoil DOT 4 Brake Fluid

Link to comment
Share on other sites

  • Replies 114
  • Created
  • Last Reply

Thank you!!! As a new owner, it's been daunting trying to figure out what fits, what's available, what brands are good to use.

 

Also, what's the milkjug delete. I've seen it mentioned several times but I don't know what it applies too. I'm assuming something with the factory airbox?

 

Ok I did a search and found one thread talking about the milkjug delete.

Link to comment
Share on other sites

Thank you!!! As a new owner, it's been daunting trying to figure out what fits, what's available, what brands are good to use.

 

Also, what's the milkjug delete. I've seen it mentioned several times but I don't know what it applies too. I'm assuming something with the factory airbox?

 

Ok I did a search and found one thread talking about the milkjug delete.

 

PM'd.

"It's within spec" - SOA :rolleyes:

"Depth is only shallowness viewed from the side." - Fredism

"So, how much did it cost for your car to be undriveable :lol:." - Stephen (very close friend)

"You have done so much it would be stupid to go back." - Sunny of Guru Electronics

 

2018Q50RS | 2015WrxThread | Shrek

Link to comment
Share on other sites

Nice build list. Keep us posted on the bushing install and first impressions.

 

Have you considered different brake pads than Hawk HPS? I've been quite pleased with the Carbotech Bobcats over the HPS. They consistently perform the same from initial braking to stop. Hawks never did that.

 

What's you time line for the Rapture super charger? There has been a false start on 3.6R headers. They seem to be essential to max performance out of the H6. Bring on the Stage II H6! Do it!!

Link to comment
Share on other sites

That rear diffuser looks good.

 

Did your car come without a wing?

"It's within spec" - SOA :rolleyes:

"Depth is only shallowness viewed from the side." - Fredism

"So, how much did it cost for your car to be undriveable :lol:." - Stephen (very close friend)

"You have done so much it would be stupid to go back." - Sunny of Guru Electronics

 

2018Q50RS | 2015WrxThread | Shrek

Link to comment
Share on other sites

Mines easy but sure. Let me know when its my turn :lol:

"It's within spec" - SOA :rolleyes:

"Depth is only shallowness viewed from the side." - Fredism

"So, how much did it cost for your car to be undriveable :lol:." - Stephen (very close friend)

"You have done so much it would be stupid to go back." - Sunny of Guru Electronics

 

2018Q50RS | 2015WrxThread | Shrek

Link to comment
Share on other sites

"Last edited by Perscitus; Today at 08:22 PM.."

What did you change?

Re-shuffled a few items around, edited some parts numbers in, and changed the brake pads that are going in. Underdog sent me the HKS Ceramics so I'll be using those.

I'm curious to see what your 1/4 mile time and trap speed would be now. Car looks very nice!
Thanks! I should have some numbers this spring when I hit a strip or race course with AZP.
Link to comment
Share on other sites

I can bring up the rear with the 2014 ;)

 

The floodgates of 3.6r info and support have opened :lol:

"It's within spec" - SOA :rolleyes:

"Depth is only shallowness viewed from the side." - Fredism

"So, how much did it cost for your car to be undriveable :lol:." - Stephen (very close friend)

"You have done so much it would be stupid to go back." - Sunny of Guru Electronics

 

2018Q50RS | 2015WrxThread | Shrek

Link to comment
Share on other sites

Yep...we get giddy on single digit power gains while the GT crowd cant decide if a sub $1000 mod gained 65 or 66whp.

"It's within spec" - SOA :rolleyes:

"Depth is only shallowness viewed from the side." - Fredism

"So, how much did it cost for your car to be undriveable :lol:." - Stephen (very close friend)

"You have done so much it would be stupid to go back." - Sunny of Guru Electronics

 

2018Q50RS | 2015WrxThread | Shrek

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.




×
×
  • Create New...

Important Information

Terms of Use