Kalien32 Posted November 6, 2015 Share Posted November 6, 2015 Hey guys. So, I just ordered some JDM visors on monday. They shipped from Dubai on tuseday. Showed up at my door Thursday. 3 days shipping! How much for brand new jdm visors? $144!! Everywhere else is $300+. Here you guys go... Sedan: https://partsouq.com/en/search/search?q=E3610AG000 Wagon: https://partsouq.com/en/search/search?q=E3610AG010 You can thank BarManBean for posting the site. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/20151105_194145_zps2kw8wvxq.jpg Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 6, 2015 Moderators Share Posted November 6, 2015 Kalien, I haven't even installed mine yet. Any tips? "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
Kalien32 Posted November 6, 2015 Author Share Posted November 6, 2015 (edited) Yeah! It's very easy install. The instructions threw me for a loop, so the 1st one took a while to make sure it was right. 2nd one took about 5 minutes. Here's the best instructions I can give. Step 1: -Pull the rubber liner down on the front and rear windows. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/20151105_184858_zpsrctixuml.jpg Step 2: -Remove the 4th screw from the front of the channel and install one of the two larger brackets. (You'll see them in the bag of hardware) Note: this was the part that confused me. The wording in the instructions makes it seem like you need to take all the screws out and remove the channel. When, in reality, you only have to remove the one screw. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/20151105_184839_zpsmkyt5bot.jpg Step 3: -Clean the black moulding above the windows. This is where the visor will stick to. Step 4: -Grab visor and look for the split in the protective tape on the double-sided sticky tape. - Peel both sides back about an inch, or two, and fold them over the top of the visor. This will allow you to grab, and remove them, after you have the visor positioned and clipped in later. Step 5: - the exposed sticky tape should now line up with the installed bracket when you hold it up to the car. - slide the back lip of the visor behind the bracket to clip it in. Step 6: - Grab the 2nd bag that contains the 10 smaller brackets. (You'll use 5 for each side of the car.) - position the visor and ad the clips. The clips grab the channel and then push up into the visor to clip it in. Note added by BarManBean: the bracket locations are NOT approximate. There is a holed drilled on the inside of each visor that connects exactly with each clip. Make sure to start each visor in the correct location and then install secondary brackets likewise. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/2015-11-06_13.13.16_zpsemrasexz.jpg Step 7: - finetune your positioning and pull the rest of the protective tape off the sticky tape to secure the visor. Step 8: - push the rubber liner back into the door frame. tip: I used my key fob to push the liner back in. I found its a lot easier than with your fingers. I'm sure there are better tools, but that's what I used. It's smooth and round, and doesn't risk tearing the rubber. Step 9: - stand back and admire your handy work. Edited November 7, 2015 by Kalien32 Link to comment Share on other sites More sharing options...
Kalien32 Posted November 6, 2015 Author Share Posted November 6, 2015 Barmanbean, How'd you find the part number to originally find the visors? The site is impossible to navigate without part numbers, and I'd love to see what else is available. Link to comment Share on other sites More sharing options...
scoobyskier Posted November 7, 2015 Share Posted November 7, 2015 How do I find more parts on that site? I need these STI Quad tip mufflers:ST4430021001.....and curious what else is available. Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 7, 2015 Moderators Share Posted November 7, 2015 Barmanbean, How'd you find the part number to originally find the visors? The site is impossible to navigate without part numbers, and I'd love to see what else is available. I know. I tried to find a couple more part numbers to look for stuff but wasn't very successful and didn't have much time. Basically if you can find the OEM part number you should be able to find it. Problem is that a lot of the JDM vendors (avojdm for example) seem to use their own reassigned part numbers and obviously those don't show up. JDM parts catalog anyone? I found the visor part number searching here on the forum, IIRC. Was looking at buying a used set here, figured I'd make sure there wasn't something out there that was competitive on price for new stuff, and stumbled on partsouq FTW! "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 7, 2015 Moderators Share Posted November 7, 2015 I think the best would be for folks that have ordered parts to post up the part numbers. For example--anyone with a double din happen to have the original packaging with the subaru part number on it?!? "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
Kalien32 Posted November 7, 2015 Author Share Posted November 7, 2015 (edited) I have a double din... I can pull it out and see if part numbers are on it... Also. I found jdm extending armrest with storage... I did enter my vin # and was able to look up every single OEM part for my car. But they were all usdm. They have them all sorted into groups and you can click on them and find specific parts... literally has EVERYTHING listed. Edited November 7, 2015 by Kalien32 Link to comment Share on other sites More sharing options...
Kalien32 Posted November 7, 2015 Author Share Posted November 7, 2015 http://legacygt.com/forums/showthread.php/legacy-part-numbers-7871.html A lot of these don't show up in the search... but some do.. Interesting note: the visor part # is different on partsouq... wonder how many of them are wrong in the list... Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 7, 2015 Moderators Share Posted November 7, 2015 Just installed mine. Thanks for the notes, Kalien! Only other tip I would add: the bracket locations are NOT approximate. There is a holed drilled on the inside of each visor that connects exactly with each clip. Make sure to start each visor in the correct location and then install secondary brackets likewise. "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 7, 2015 Moderators Share Posted November 7, 2015 I have a double din... I can pull it out and see if part numbers are on it... Also. I found jdm extending armrest with storage... I did enter my vin # and was able to look up every single OEM part for my car. But they were all usdm. They have them all sorted into groups and you can click on them and find specific parts... literally has EVERYTHING listed. I guess what we need is a vin number for a JDM car? "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
Kalien32 Posted November 7, 2015 Author Share Posted November 7, 2015 Good note! I didn't even notice... I'll have to go back and make sure I did it right.. although, I doubt mine is going anywhere. I have some friends with jdm cars. And some in Europe. Maybe they would share their Vin with me and I can find some parts... Link to comment Share on other sites More sharing options...
anti Posted November 7, 2015 Share Posted November 7, 2015 From what I've read on this site, the E3610AG000 & E3610AG010 are the EDM part numbers. Sounds like they're suppose to be the the same though. I've thought about getting them a few times, I guess they could be for Christmas.. Link to comment Share on other sites More sharing options...
Kalien32 Posted November 9, 2015 Author Share Posted November 9, 2015 Got our first hard rain tonight, after installing my visors.. was very happy with how much you can vent the windows while on the freeway... this was extremely heavy rain. I didn't feel any water. Had the drivers side down just as much.. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/20151108_201229_zpsojtqstt1.jpg Link to comment Share on other sites More sharing options...
quick4dr Posted November 10, 2015 Share Posted November 10, 2015 Great price. Valley legacy got me mine about 2 years ago. They look the best, and I get about the same amount of window down rain free Link to comment Share on other sites More sharing options...
turboboost Posted November 10, 2015 Share Posted November 10, 2015 The visors look great and I want a set, but I also use a Yakima roof rack throughout the year for snowboarding and cycling. 1st world sedan problems. Link to comment Share on other sites More sharing options...
Kalien32 Posted November 10, 2015 Author Share Posted November 10, 2015 The visors look great and I want a set, but I also use a Yakima roof rack throughout the year for snowboarding and cycling. 1st world sedan problems. Sounds like it's time to get a wagon. I had the same first-world-sedan-problem before I got my wagon.. wanted the visors really bad. But I go to the slopes every year... Link to comment Share on other sites More sharing options...
turboboost Posted November 10, 2015 Share Posted November 10, 2015 Ha, I am seriously contemplating it. Most of my parts would be a direct swap to an 05LGT wagon (if I can find one). An OBXT wouldn't be bad either, but wouldn't be a direct swap for a lot of my current mods. Link to comment Share on other sites More sharing options...
discojon Posted November 10, 2015 Share Posted November 10, 2015 I ordered a set for the wagon yesterday, said there was one left in stock. Got an email this morning that the order was cancelled due to no stock. Who got my Wagon Visors!!! Link to comment Share on other sites More sharing options...
Moderators BarManBean Posted November 10, 2015 Moderators Share Posted November 10, 2015 I ordered a set for the wagon yesterday, said there was one left in stock. Got an email this morning that the order was cancelled due to no stock. Who got my Wagon Visors!!! Boooo! Maybe they will restock. "Bullet-proof" your OEM TMIC! <<Buy your kit here>> Not currently in stock Link to comment Share on other sites More sharing options...
anti Posted November 10, 2015 Share Posted November 10, 2015 I ordered a set for my sedan yesterday since the quantity had dropped since I first looked. 6 sedan sets left now. Link to comment Share on other sites More sharing options...
Kalien32 Posted November 11, 2015 Author Share Posted November 11, 2015 I ordered a set for the wagon yesterday, said there was one left in stock. Got an email this morning that the order was cancelled due to no stock. Who got my Wagon Visors!!! They will restock. And you will get an email when they do... same thing happened to me. Willing to bet it'll be about a week. Link to comment Share on other sites More sharing options...
scoobyskier Posted November 11, 2015 Share Posted November 11, 2015 I received mine today, literally the best packing job I have ever seen. Wood encased box wrapped in plastic and taped! What other parts can we get from this site? Link to comment Share on other sites More sharing options...
Kalien32 Posted November 12, 2015 Author Share Posted November 12, 2015 (edited) I received mine today, literally the best packing job I have ever seen. Wood encased box wrapped in plastic and taped! What other parts can we get from this site? Right?!?! I loved that! And the wood is good wood for making parts for my rc planes! I found center console extending armrest with extra storage.... both black and tan. Edited November 12, 2015 by Kalien32 Link to comment Share on other sites More sharing options...
housemusic1 Posted November 12, 2015 Share Posted November 12, 2015 Hey guys. So, I just ordered some JDM visors on monday. They shipped from Dubai on tuseday. Showed up at my door Thursday. 3 days shipping! How much for brand new jdm visors? $144!! Everywhere else is $300+. Here you guys go... Sedan: https://partsouq.com/en/search/search?q=E3610AG000 Wagon: https://partsouq.com/en/search/search?q=E3610AG010 You can thank BarManBean for posting the site. http://i1321.photobucket.com/albums/u542/Kalien32/Mobile%20Uploads/20151105_194145_zps2kw8wvxq.jpg Do these visors allow you to have the window fully rolled up, and still close the door? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now