madrig Posted May 10, 2017 Share Posted May 10, 2017 (edited) To help people to do the black interior conversion for the headliner and pillars ,i will explain the way i did it and hope other members will share their experience also . so everybody know what it look like in the legacy gt . i m a fan of the black interior headliner but be aware it can be a drastic change . your interior will never look the same ! so for start the complete list of interior parts . these parts number are for the S402 , so all pillar are covered with sti grey fabric . i beleive you can get the pillar only black plastic but can not confirm ( will post parts number for ALL black pillar later on ) ho ,forget to mention i own a wagon ! A pillar right 94010AG041JC left 94010AG051JC B PILLAR right 94012AG140JC cap 94067AG100JC left 94012AG051JC cap 94067AG110JC C pillar right 94013AG100JC cap 94067AG140JC (cap sedan ) 94076AG120JC cap wagon left 94013AG110JC cap 94067AG150JC (cap sedan ) 94067AG130JC cap wagon D pillar RIGHT 94015AG001JC LEFT 94015AG011JC Rear gate RIGHT 94330AG001JC LEFT 94330AG011JC CENTER UPPER 94310AG001JC Sedan` C pillar( didn t forget you guy ! ) RIGHT 94013AG600JC cap 94067AG140JC LEFT 94013AG610JC cap 94067AG150JC Cover right 94053AG541JC left 94053AG551JC Sun visor right 92011AG210JC cap 92011PA000JC hook 92018AG000JC left 92011AG120JC cap 92011PA000JC hook 92018AG000JC assist rail hook less 92041AG000JC assist rail hook 92041AG010JC cap damper side 92073AG020JC cap spring side 92073AG030JC lamp assembly Map 84621FG131JC (from USDM STI ) lamp assembly room 84601AG040JC lamp assembly luggage room 84671AG040JC sun shade handle #? (sti 2017 have one ) garnish sun roof #? Black Edge(http://www.trimlok.com) baseholder belt roof 94472AG121JC (non sunroof trim) cover holder belt roof 94472AG100JC(non sunroof trim) cap belt trim panel roof 94482FC001JC(non sunroof trim) cover child anchor 94461AG040JC cap emergency #? ( ebay/ fastenal/not really needed) roof end #? ( find use one from japan) Edited February 6, 2019 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) Edited May 10, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) you dont need to purchase all pillar . A pillar , cover yours with fabric B pillar needed to have a least the sliding center section black , buy black cap C pillar cover yours with fabric , buy black cap usdm sti , 2008 to 2014 , share the same components . map light , dome light , trunk light handle , but i think sti dont have the handle with hook . sun visor should be the same , i know the cap is different , so can not comfirm untill somebody try . 2016 wrx , picture from car101.com, the sunvisor look the same as legacy with the extension , but never see that in real life . Edited May 13, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) Cap pillar i never find the parts number for wagon cap C pillar:cool: a mystery ! . so i used the cap of sedan C pillar . need to be modified cause is different , the way it clip on . i grinded a litlle the pillar slot and modified the cap and reinforced it with epoxy . also the shape is a little different so i clamped on place over night . the C pillar need to be disassembled to re cover with fabric . you will need to grind the palstic spot in the back and after glue it back with epoxy . Edited May 10, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) the jdm sunvisor hook dont fit . i compared to sti usdm but different , so use the jdm one . to make it fit i had to sand 1 milimeter of the pastic clip . better to show you with pic sand all the tab around , remove 1 mm and try on . Edited May 11, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) for the seat belt located on the roof i used the black cover jdm that are made for the non sunroof trim . they are different parts , so i had to re shape the headliner . i made a plug and a mold of the section . did a fiberglass parts bonded on the headliner and blended. Edited July 9, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) seat belt upper attachment . before after i decided to switch the seat belt upper attachment. so in order to proceed i had to buy a use set of jdm seat belt . the jdm can not be swap complete( for my knowledge) cause some small difference . please refer to pics . the jdm have a tensionner for the driver side , what i dont have on my 06 and anyway it will be passenger side for me . do this mod if you feel confident and judge for yourself the safety result . in order to unroll the belt you need to remove the ratchet system , after that iis easy to unroll the belt and to access the pin to remove the belt from the roler . clamp lightly the gear cause it still spring actuated . the hanger can not be removed , the end of the belt is too thick to pass . for the usdm you can destroy the hanger to get it out , you dont need it . for the jdm , cut the belt , take it out and slot the opening 3mm (1/8) so you can pass the belt thru to reassemble . i did the opening with a hand grinder , i m use too but is very risky! best is to go to a machine shop , and only slot the top of the opening belt not the side where the belt will slide . do this at your own risk . you can also wash it to make it softer and better to roll in ! Edited May 11, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) map light i used a map light from an STI . everything is plug and play , cause is a sedan one of the sunroof switch have no use . i also decided to switch the airbag lighting to the same place , the sti section is a mic and the section can not be remove , so with a little bit of grinding and drilling all fit in place . the inner section was paint black to make it darker . Edited May 11, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) of course i did not include all the step about this process , like take the headliner out and other small detail but you will have a good starting point for your own project . Edited May 11, 2017 by madrig Link to comment Share on other sites More sharing options...
madrig Posted May 10, 2017 Author Share Posted May 10, 2017 (edited) to be updated Edited May 11, 2017 by madrig Link to comment Share on other sites More sharing options...
Andy_Mac Posted May 11, 2017 Share Posted May 11, 2017 Good stuff. Glad to see some others are starting to take on the swap. 2000 Legacy B4 RSK - SOLD 2006 Legacy BP5 GT Spec B wagon - Garage Thread 2011 VW T5 van 2.0L of turbo diesel awesomeness Link to comment Share on other sites More sharing options...
madrig Posted May 11, 2017 Author Share Posted May 11, 2017 map light in action . Link to comment Share on other sites More sharing options...
madrig Posted May 15, 2017 Author Share Posted May 15, 2017 (edited) saw a new sti at dealer . you can use the handle from the shade sunroof , but it s not sold separetely .so need to source used if you go this route . the sunvisor have different cap from the legacy , it s still only two screws to attach to the body but dont know if it will fit lgt . Edited May 15, 2017 by madrig Link to comment Share on other sites More sharing options...
digdug18 Posted May 20, 2017 Share Posted May 20, 2017 Seems like a lot of work to me. Why not just paint the parts that you have black? SEM makes excellent paint for exactly this use. Link to comment Share on other sites More sharing options...
madrig Posted May 21, 2017 Author Share Posted May 21, 2017 Seems like a lot of work to me. Why not just paint the parts that you have black? SEM makes excellent paint for exactly this use. look like a lot of work but is not . there is no need to paint the parts , there are available in black . this thread is intended for people that seek a oem quality like myself . Link to comment Share on other sites More sharing options...
zactek Posted May 22, 2017 Share Posted May 22, 2017 look like a lot of work but is not . there is no need to paint the parts , there are available in black . this thread is intended for people that seek a oem quality like myself . The price difference would probably be huge. I would bet that all those interior pieces would probably run close to a grand. I know the sun visors are around $125 each. For the price of 3 or 4 SEM cans,you can probably do the whole interior. Zack K. Link to comment Share on other sites More sharing options...
madrig Posted June 2, 2017 Author Share Posted June 2, 2017 The price difference would probably be huge. I would bet that all those interior pieces would probably run close to a grand. I know the sun visors are around $125 each. For the price of 3 or 4 SEM cans,you can probably do the whole interior. Zack K. yes price wise big difference , would like to see if somebody succeed to paint all this parts and what it look like . i m sure you can get a good result but i m worry how it will age . Link to comment Share on other sites More sharing options...
jonnyt88 Posted June 26, 2017 Share Posted June 26, 2017 The price difference would probably be huge. I would bet that all those interior pieces would probably run close to a grand. I know the sun visors are around $125 each. For the price of 3 or 4 SEM cans,you can probably do the whole interior. Zack K. what SEM product would you use? Link to comment Share on other sites More sharing options...
madrig Posted June 28, 2017 Author Share Posted June 28, 2017 sometime you dont have to look too far to find it . the sedan usdm base holder is black and fit the wagon ! you will have to slot the piece to insert the belt for installing the headliner . no easy to install cause you will have to insert thru the belt at same time you positionning the headliner ! but can be an idea if you dont want to modify like i did . HOLDER-COVER,REAR SHELF Part Number: 65556AG08AJC BASE HOLDER-SUN ROOF Part Number: 94472AG54AJC Link to comment Share on other sites More sharing options...
zactek Posted June 28, 2017 Share Posted June 28, 2017 what SEM product would you use? For most hard vinyl,plastic items as well as smaller fabric pieces I would use SEM color coat #15243, satin black. I think it matches the factory black fairly well.I haven't used it on larger fabric areas like the headliner,so not too sure how it would look. Things like the dome light and possibly high wear parts might be better bought in OEM black. Zack K. Link to comment Share on other sites More sharing options...
tysparks81 Posted June 28, 2017 Share Posted June 28, 2017 This is a great write-up and should be sticky'd. Amazing work. I'm going to be doing this just trying to find spare interior trim parts to minimize my down time. #LGTSTi is still cheaper and nicer then an equal year wrxsti Follow my 2007 Spec B. Build here Link to comment Share on other sites More sharing options...
Underdog Posted June 28, 2017 Share Posted June 28, 2017 Impressive! Looking forward to the finished product, but I really appreciate the detailed process. The Crimson Dynamo Link to comment Share on other sites More sharing options...
BagRidersJohn Posted June 28, 2017 Share Posted June 28, 2017 Ho-ly shit!!! I've had the upper trim from my wife's totaled BL sitting here in my office for like 8 months waiting to be blackened-- I actually wrapped the A pillars last night but now I don't think I'll be using them. This thread is absolutely incredible man, thank you **so much** for the part numbers! I've done DIY interior wraps before and while they always come out looking just fine, its really nothing compared to the quality of OEM especially for an OEM+ nut like me (and you, obviously). Thank you again for taking the time to put together such a comprehensive list of parts and fine details, you are the real MVP!! My 2007 specB (full undercarriage & drivetrain refinish, every nut and bolt replaced, full engine rebuild/restore, glass-out respray, air ride, wide body, and more! All done by me, at home!) Instagram: @bagriders_john for more Subarus (and also my wife and cat) Link to comment Share on other sites More sharing options...
jonnyt88 Posted June 29, 2017 Share Posted June 29, 2017 For most hard vinyl,plastic items as well as smaller fabric pieces I would use SEM color coat #15243, satin black. I think it matches the factory black fairly well.I haven't used it on larger fabric areas like the headliner,so not too sure how it would look. Things like the dome light and possibly high wear parts might be better bought in OEM black. Zack K. Not to derail the OPs post of getting the parts, I did a lot of MR2 with Duplicolor Vinyl/Fabric spray. It came out fairly well for $25. Maybe I'll write up my experience Link to comment Share on other sites More sharing options...
madrig Posted July 3, 2017 Author Share Posted July 3, 2017 This is a great write-up and should be sticky'd. Amazing work. I'm going to be doing this just trying to find spare interior trim parts to minimize my down time. let me know what you looking for . Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now