monkeyposeur Posted October 2, 2012 Share Posted October 2, 2012 As many of you know I am gathering parts to swap my 22T into my wagon. I'm not sure of the direction that I will go with the build and I'm not in a rush because I want to think it through and end up with something reliable. However, I have been checking out 20Gs on ebay and they can be had fairly cheaply. In some instances I have found a complete 20G w/trans, ecu, and wiring harness for $1600. This has me considering going in that direction instead of building up the 22T. I could sell the 22T block halves for $600-700 just by themselves. I have a few options with the 22T that I am considering: 1. Keeping everything stock (heads, ecu, etc.), but add a tmic and tdo4, which would be plenty of fun compared to my 22E. 2. Getting some wrx heads, ecu, intake mani, and using the 22T. Option 1 would be the cheapest, but also the most limited. Option 2 would give me tuning options and would be even more fun. But option 2 would also cost about the same as getting a complete 20G w/trans from ebay (probably need a standalone, would the 20G ecu work?). Anyone have any opinions on 22T vs 20G? Thanks! Link to comment Share on other sites More sharing options...
DOHCEJ22E1 Posted October 2, 2012 Share Posted October 2, 2012 How about 22T block w/20G heads, 20G wiring harness, 20G ECU/aftermarket ECU, & having FUN with that combo? You can sell the 20G block & support your hybrid even more. That would be VERY CLOSE to the 22B engine. Just food for thought Link to comment Share on other sites More sharing options...
subikid90 Posted October 2, 2012 Share Posted October 2, 2012 EJ22T with the 205 heads will be a tougher engine and probably be easier to tune/wire than the EJ20G. Of course I am kind of biased lol -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
DOHCEJ22E1 Posted October 2, 2012 Share Posted October 2, 2012 EJ22T with the 205 heads will be a tougher engine and probably be easier to tune/wire than the EJ20G. Of course I am kind of biased lol Truth. With 205 heads & wiring, he'll be able to enjoy easier tuning & slightly more compatibility with later hardware/software but 20G! LOL! How often do you come across a 20G? 205s can be found in almost every junkyard in this country! Which makes the 205 more appealing... Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 3, 2012 Author Share Posted October 3, 2012 Thanks for the opinions guys. As far as 205s in the junkyards I have yet to come across a single one and I frequent them often. It's probably because there are so many subie enthusiasts out here that they never make it to the bone yard. I've looked for 20G heads but have yet to find any. As far as tuning the 205 route, are there base maps that I could use before I got it up on a Dyno? From what I understand a Dyno tune is $500-600 each time? It would be nice to be able to drive it to get tuned the first time without it blowing up, lol. I think I can find a 20G ecu easy enough, and then get it Robtuned. But a wrx ecu is even easier to come by, and a lot cheaper. A wrx wiring harness is also fairly easy to find. I really want to use this 22T block if I can. Link to comment Share on other sites More sharing options...
subikid90 Posted October 3, 2012 Share Posted October 3, 2012 I will have a base map for mine (already have it but not sure if it is correct till I have the motor running) that I can pass along to you. It should give you a start. I am thinking about doing a speed density tune, there is a local shop here, Synergy Tuning, that does them and guys are loving the gains. They will also have a dyno soon. Dyno time is about $75-150 an hour depending on the place, plus $200 or so for the tune. I have noticed tuners like to work a little extra for different setups, aka EJ22T w/ 205 heads, because it adds to their base maps for other people. -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 3, 2012 Author Share Posted October 3, 2012 The 22T internals are pretty beefy. I'd like to use them to keep thing simple for my own benefit, but aren't you planning on doing a stroker build? What are you doing for internals? Link to comment Share on other sites More sharing options...
Kennyfvholla Posted October 3, 2012 Share Posted October 3, 2012 Stay with the 22T bottom end, and maybe add some ACL race bearings throughout. Put 20g heads on it. Follow all that up with upgraded fun stuff like a bit of porting, injectors, fuel pump, etc. You know what I'm talking about. Also, make sure you get a nice aluminum radiator to keep it cool. Link to comment Share on other sites More sharing options...
99legacyturbo Posted October 3, 2012 Share Posted October 3, 2012 I have a 22t with 20g heads and I'm super happy with it way happier than I was with just a 20g. Your compression drops from 8:1 on the 20g to like 7-7.5:1 having the 20g heads on the 22t cause of the thicker head gaskets you'll need but you'll be gaining engine size going from a 2.0 to like a 2.3ish. So in my experiance I spool alot faster and have more torque with the 22t with 20g heads. And it really wasn't hard at all to find the right parts and the wireharnes I just made myself anyway cause I'm standalone. I also could send my maps I have one for 10psi and one for 20psi. Any questions you have about doing the hybrid feel free tO ask Link to comment Share on other sites More sharing options...
SpecBamf41 Posted October 3, 2012 Share Posted October 3, 2012 what do you think about a ej205 and 25d heads? im having better luck finding 2.slow blocks then 2.5. only thing is trying to spool my turbo with a 2.0 might be hell BNR18g on 93oct Link to comment Share on other sites More sharing options...
DOHCEJ22E1 Posted October 3, 2012 Share Posted October 3, 2012 what do you think about a ej205 and 25d heads? im having better luck finding 2.slow blocks then 2.5. only thing is trying to spool my turbo with a 2.0 might be hell Do not use 96 25D heads on a 205. The 25D head chambers are bigger than the 205 bore. The 97-99 25D heads may be a more direct fit but you'd have to place 205 gaskets on them to make sure that the chambers are within the bore. These are 22e MLS head gaskets on the 97-99 25D heads. Note how the chambers are enclosed within the bore with a little extra space. http://i172.photobucket.com/albums/w40/Kenshin1984/DOHC%20EJ22E/EJ22Egasketon25Dhead.jpg Link to comment Share on other sites More sharing options...
subikid90 Posted October 3, 2012 Share Posted October 3, 2012 Do not use 96 25D heads on a 205. The 25D head chambers are bigger than the 205 bore. The 97-99 25D heads may be a more direct fit but you'd have to place 205 gaskets on them to make sure that the chambers are within the bore. These are 22e MLS head gaskets on the 97-99 25D heads. Note how the chambers are enclosed within the bore with a little extra space. http://i172.photobucket.com/albums/w40/Kenshin1984/DOHC%20EJ22E/EJ22Egasketon25Dhead.jpg ^Agree 100%. You can use heads from a smaller bore, but you should have them matched to the bore. There are a few companies that do this with a CNC machine. The 22T internals are pretty beefy. I'd like to use them to keep thing simple for my own benefit, but aren't you planning on doing a stroker build? What are you doing for internals? Yes I am doing forged internals. EJ257 Nitrated crank, ACL bearings rod and mains, wiseco pistons, and scat rods. I am on the verge of having custom rods made or custom pistons. GSC S2 cams, BC springs and retainers, Supertech valves and shimless bucket conversion. -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 3, 2012 Author Share Posted October 3, 2012 Sounds awesome subikid! If I used 20G heads w/the 22T can I use the 22T intake manifold or do you need the 20G intake mani? Also, do you use 22T or 20G HGs, I would think the 22Ts? 99legacyturbo, what other parts did you need? Did you use the 22T coilpack as well? Link to comment Share on other sites More sharing options...
DOHCEJ22E1 Posted October 3, 2012 Share Posted October 3, 2012 Sounds awesome subikid! If I used 20G heads w/the 22T can I use the 22T intake manifold or do you need the 20G intake mani? Also, do you use 22T or 20G HGs, I would think the 22Ts? 99legacyturbo, what other parts did you need? Did you use the 22T coilpack as well? If you use 20G heads, you must use the 20G intake manifold as well. You use 22T head gaskets. Head gaskets must match the block because of the bore size. Link to comment Share on other sites More sharing options...
subikid90 Posted October 4, 2012 Share Posted October 4, 2012 Yes you almost always have to match the intake mani to the heads. -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 4, 2012 Author Share Posted October 4, 2012 Ok. So the 20G heads are great, but I would also have to find the matching intake mani. That might be hard to find, but doable. I can easily find 205 heads and intake mani since they are plentiful. I found some on bbs actually, but I have spent enough this month on subies so I want to wait and save a bit before I buy them and they might not be available then. I'm trying to limit my impulse subie spending, lol. So what would the advantage of 20G vs 205 heads be? The main advantage of the 20G heads would be that I could use a stock 22T ecu to run them. Other than that, what would be the pros and cons? Another thing, what about the dash unit for either swap? Can I use the stock gauges (mph, rpms, etc.) or will I need the matching dash unit? I wouldn't mind a wrx dash actually. Link to comment Share on other sites More sharing options...
subikid90 Posted October 4, 2012 Share Posted October 4, 2012 You can use everything that is currently on your car besides the fuel, ecu and engine stuff. Contact Brian at Iwire, he can do the wiring merge for $650ish. -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 4, 2012 Author Share Posted October 4, 2012 I was thinking about pulling a wiring harness from a junkyard legacy and having that merged then when I do the swap there will be less downtime. Would I need to send the complete wiring harness? Everything? edit: I read the Wiring Harness Merge How To in the Turbo FAQ by Brian of IWire. I will probably have him do the merge to save myself some headache. It looks like a PITA especially if it is your first time. The more I look into it the more the WRX USDM route seems the way to go for ease of finding parts, tuning possibilites, etc. Link to comment Share on other sites More sharing options...
SpecBamf41 Posted October 4, 2012 Share Posted October 4, 2012 http://forums.nasioc.com/forums/showthread.php?t=2415763 BNR18g on 93oct Link to comment Share on other sites More sharing options...
DOHCEJ22E1 Posted October 4, 2012 Share Posted October 4, 2012 http://www.rs25.com/forums/f128/t104612-ej22t-wire-harness-updated-ej20g-heads.html Apparently, 20G heads can & will run on a 22T with no issues at all. Just need a little fine tuning. Read Susiemk's posts. Link to comment Share on other sites More sharing options...
SpecBamf41 Posted October 4, 2012 Share Posted October 4, 2012 Is high compression motors taking over the 2nd gen forum. I'm starting to get the bug too. Anyone one wonder about ej18 heads on a 25? Who all is going high compression? Sent from my SCH-I800 using Tapatalk 2 BNR18g on 93oct Link to comment Share on other sites More sharing options...
99legacyturbo Posted October 4, 2012 Share Posted October 4, 2012 I got custom head gaskets cause you need thicker ones cause on the 22t the pistons come above the deck. Call rallyspec they told me what gaskets to use and had them for pretty cheap and they were cosworth so I know there good. And for intake manifold I used the stock manifold of the ej25 that came out of my car originally it's prolly way easier to find and cheaper than a ej20g intake manifold. And as far oil pump goes your Gunna wana get a ej25 Sti oil pump cause you'll need the extra flow for the piston sprayers and dohc heads. Link to comment Share on other sites More sharing options...
twisty Posted October 4, 2012 Share Posted October 4, 2012 Is high compression motors taking over the 2nd gen forum. I'm starting to get the bug too. Anyone one wonder about ej18 heads on a 25? Who all is going high compression? Sent from my SCH-I800 using Tapatalk 2 im staying bone stock on my L wagon. its front wheel drive, no real point in doing huge engine mods. ill do suspension and some bolt ons, give it a good paint job and such. then look for a good awd base to build up as a project. im thinking of going rally with whatever i find, that way i can use it for work as well. theres some sites i work at that i cant even get my dodge truck down to without getting stuck. Link to comment Share on other sites More sharing options...
monkeyposeur Posted October 5, 2012 Author Share Posted October 5, 2012 I got custom head gaskets cause you need thicker ones cause on the 22t the pistons come above the deck. Call rallyspec they told me what gaskets to use and had them for pretty cheap and they were cosworth so I know there good. And for intake manifold I used the stock manifold of the ej25 that came out of my car originally it's prolly way easier to find and cheaper than a ej20g intake manifold. And as far oil pump goes your Gunna wana get a ej25 Sti oil pump cause you'll need the extra flow for the piston sprayers and dohc heads. Good stuff to know. I put Subaru HGs on my SS. I cleared my basement out so I can move the 22T block down there and put it on an engine stand and start to get to work on it. I want to start with installing ACL race bearings. There are a few options. What would you go with? Rods: http://www.rallysportdirect.com/1993-Subaru-Legacy-Sport-2.2L_Rod-Bearings Mains: http://www.rallysportdirect.com/1993-Subaru-Legacy-Sport-2.2L_Main-Bearings Link to comment Share on other sites More sharing options...
subikid90 Posted October 5, 2012 Share Posted October 5, 2012 You have to measure the mains and rods to figure out what size you need. For rods and mains I just take the motor to the machine shop and have them do it. Make sure you tell them the clearances you want for the rods and mains. I am assuming you are going with the stock EJ22T crank? If not look into King bearings, they have a good bearing that has better quality control than ACL does. -Subikid90 1997 Legacy GT 5spd & EJ251 w/EJ25D heads ~10.5CR 1998 Legacy GT Limited waiting for EJ22T hybrid swap Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.