Jump to content
LegacyGT.com

thombob

Members
  • Posts

    26
  • Joined

Personal Information

  • Location
    Southern California
  • Car
    2016 Legacy 2.5i Limited
  • Interests
    Skate | Surf | Snowboard

thombob's Achievements

Apprentice

Apprentice (3/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Lol. Drove around the entire neighborhood and this was the "spookiest" house that I came across. http://images.tapatalk-cdn.com/15/10/29/43b821ef123088f205d3364fa829b9e4.jpg
  2. I left everything over night and attempted to try again this morning. I ensured that the setup was properly grounded on both sides, and tried once more. Still nothing. Then all of a sudden I was struck by bad luck. FML. I unclipped the clip from the hazard connect and to my $%&*!$# luck, it fell down... To add onto that, the pair of glasses I currently wear has a loose right lens. As I stared into the center console moving my head up/down, I slightly bumped the windshield and my right lens popped out sliding down into that @$%! hole! I am over this... for now. What should I do to go about removing my lens and clip from the center console? I have no idea where they fell down, and I expect that once I start driving I will hear an occasional rattle here and there...
  3. I just finished trying to reconnect the wire to the hazard cable several more times. Nothing. I decided that for the hell of it I would try to connect the wire to each of the other 3 (wires)ports and still nothing! I am really bummed out about not getting this to work. I am really curious as to where I am going wrong. My Legacy being a 2016 shouldn't at all be a problem, right? At this point I am considering im2cool's kit just for the DIY video.
  4. I've switched the bulbs 180 degrees on both the left and the right. I even tried another set of bulbs. Still no luck! :/ @DA_MAXX I do not have a multimeter. I'm wondering if the sockets are not working? I'm pretty stumped lol.
  5. I've come to ask for help! This is my second time around going about this project. The first time I had used vinyl crimp connectors and electrical tape (I was too eager to begin the project and too lazy to search for all the proper materials), which is why my second time around I made sure I did everything properly. This is my first time working with wire. I watched several YouTube videos on how to splice a wire with a heat shrink connector. I also made sure I obtained all the proper tools I needed. However, I am still not getting the footwell lights to come on. I'm certain the wire is connected and touching the hazard connector wire, as I've tried moving it around and retrying it several times, but I am still not getting it to work :O I purchased the ready to go sockets. The pigtail was not long enough to reach the ground so I extended it. Was I not supposed to? I'd appreciate any advice. I'm dying to get it to work! http://images.tapatalk-cdn.com/15/10/02/287b25b8a085ccab2e402224682cf7f1.jpg
  6. I already had the in-line fuse holder in my cart and didn't even realize that was it. I still have a lot of things to learn lol. Thanks AirBorne, I appreciate it!
  7. I apologize for asking such a foolish question. I've never worked with wire before but this seems doable, and looks amazing. Will this suffice for the crimp connector? If not, could someone please direct me to the proper connector? Nybz, what is that black component? Where can I find that? http://ecx.images-amazon.com/images/I/21WAKCQ3FIL._AC_UL160_SR160,160_.jpg Thanks!
×
×
  • Create New...

Important Information

Terms of Use