Jump to content
LegacyGT.com

05LegacyGTGa

Members
  • Posts

    150
  • Joined

About 05LegacyGTGa

  • Birthday April 15

Personal Information

  • Location
    Dacula, GA
  • Car
    2005 Legacy GT Limited Wagon
  • Interests
    Mountain Biking, cars and anything outdoors
  • Occupation
    GIS Analyst

05LegacyGTGa's Achievements

Collaborator

Collaborator (7/14)

  • Dedicated Rare
  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done

Recent Badges

0

Reputation

  1. Looks like the one for the auto is $476.28. Is that grease tip needed for it?
  2. Awesome. Thanks! That was the one I was starting to lean towards after reading more posts!
  3. It seems like a couple of people have had a good experience with the stockish replacement from the driveshaft store. I'm guessing this would be the one for my car: https://driveshaftstore.com/Subaru-Legacy-Driveshaft-2005-111530 I like the idea of the solid aluminum 1 piece from the driveshaft shop, but it is more pricey. Link to the one from the driveshaft shop: https://www.driveshaftshop.com/import-driveshafts/subaru/legacy-2005/2005-subaru-legacy-2-5-gt-1-piece-aluminum-driveshaft-5-speed-automatic-only
  4. I have an 05 GT Limited Wagon with squeaking and rattling coming from the carrier bearing. Its also a 5EAT. Should I pull the trigger on the one from the driveshaft store? I was also looking at the 1 piece from the driveshaft shop, but its more pricey.
  5. I have a lot of squeaking from my driveshaft on my car. I'm assuming its the carrier bearing. It also sounds like an aluminum can rattling under the cup holder under load. I'm going to replace it, but I can't figure out which way to go. I was looking at the Dorman replacement, but have heard people say they have problems with vibration with those. Then there's the stock Subaru replacement that is pricey. Also looking at the 1 piece driveshaft from the driveshaft shop, but my car is completely stock and not sure if the 1 piece changes anything. I recently saw a thread about getting one from the driveshaft store. They seemed to be happy with that one and its not terribly priced. Which route should I go?! I've looked at so much information now that I can't process anything anymore, ha. Thanks!
  6. Anyone have issues with the steering wheel center/airbag piece getting sticky/tacky like the dash?
  7. That had to be you! I thought I saw aqua wheels! It was near Taco Bell on Mentor Ave. Probably around March 7th. The roads suck so bad up there!
  8. Anyone here have a SWP Wagon in the Mentor area?
  9. Hmmmmm....I don't have one. I guess I should contact the dealership that replaced the dash?
  10. Mine is doing the same thing on the drivers side. Quiet and tight after first putting them on. I don't really have a clunk, but more of a squeak and pop maybe? I'm not sure, its kind of hard to describe. I've gotten under it and checked all bolts and it still does it. Very irritating!
  11. Is there supposed to be a VIN plate on the dash?
  12. Well, looking at the history of this car, it spent a good while in Maine....
  13. Got mine installed! Everything seems fine with them. Simple to install. Everything seemed to fit right. Now getting my old ones off....holy crap, I was about to just get rid of the whole car...Looked to be the originals. Car has 202,000 miles on it. Freeing those balljoints was a PITA!!!
×
×
  • Create New...

Important Information

Terms of Use