ammcinnis

Read the entire thread at the link I posted. I haven't done the repair myself (yet), but those who have report that it's pretty simple. You do have to remove the shift knob, but after that only a few tools are required ... beyond a couple of plastic pry tools for trim removal.

The indicator light assembly consists of an LED soldered to a small printed-circuit board, plus an optical lens/diffuser to distribute the light. The most common failure mode seems to be cracks developing in one or more solder joints on the PCB. Over on the Outback forum, several owners have reported successful repair by simply reflowing the solder joints using a low-wattage, fine-tipped soldering iron. (A steady hand is also required; blacksmiths need not apply.) YMMV. https://www.subaruoutback.org/threads/gear-shift-indicator-light-out.473017/page-5#post-6452992 A crack is visible at the lower left of the image below:

According to Subaru of America PR, in calendar year 2023 they sold 161,814 Outbacks vs. just 25,510 Legacys. That's a ratio of 6.3 to 1. The only lines with fewer sales than Legacy were all niche vehicles: WRX (24,681), Solterra (8.872), and BRZ (4,188). The Legacy accounted for barely 4% of Subaru's total U.S. sales for the year. Subaru_December_2023_Sales_FINAL.pdf For the first three months of 2024, the numbers were even worse: a whopping 35,213 for Outback vs. 4,398 for Legacy ... a ratio of 8:1. Legacy represented only 2.9% of total U.S. Subaru sales. Only Solterra and BRZ sales were below Legacy' dismal numbers. Comparing year over year numbers, Subaru's total sales were up 6.7% for the first quarter of 2024, but Legacy sales were down 13.1% ... continuing a grim multi-year trend. Subaru_March_2024_Sales_FINAL.pdf

Given recent production/sales numbers, it seemed inevitable. R.I.P. Legacy. https://media.subaru.com/pressrelease/2165/1/subaru-announces-legacy-production-end-2025 2025_Legacy_Discontinuation_Release_-FINAL.pdf

There is an entire chapter of the FSM devoted to Power Seat Memory (PSM) diagnositcs. (See attachment.) Some PSM faults will set a DTC, but it's not clear whether or not a basic scan tool can access them if set. One possible fault is low battery voltage, so that would be something simple to eliminate before going any further. Next, I would replace the fob battery with new, just to be sure, to eliminate that as a possibility. 6.19-PSMdiag-Power_Seat_Memory_Diagnostics.pdf

NOT TRUE ... as long as all four tires are identical (same brand, model, and size) and the measured circumference of all four tires is within 1/4 inch (or measured tread depth within 1.3/32 inch). It should go without saying not to mix summer and winter tires (i.e. on the same car at the same time); it has to be one or the other. FWIW, both 225/50R18 and 225/55R17 were OE tire sizes for MY 2015-2019 Legacys, depending on vehicle trim level. The 17 and 18 inch OE wheels and tires are interchangeable, as long as all four match. If in doubt, consult the Owners Manual.

Refer to page 3 of the TSB I posted a link to.

I think that's not a good assumption. Similar? Maybe. "The same"? Probably not. (I'm not about to go out chasing part numbers for you to compare.) You can replace the "tension spring" that's at the heart of the problem yourself for less than $100 ... including the cost of the special tool required. Or you could pay a good independent shop (or even the dealer) for an hour of labor to replace it for you. That's what I would do ... but it's your car, your choice.

If you read the TSB, this specific problem is limited to Legacy, Outback, and WRX. I agree that the rattle can be annoying when driving over irregular road surfaces. A reminder: Subaru doesn't design or manufacture the Outback's steering rack. They source it from KYB.

See: Subaru TSB 04-17-17R 08/20/19 It is important to note that Subaru states "the condition is NOT detrimental to the operation of the [Electric Power Steering] system" ... i.e. it is safe to drive. FWIW, my 2016 Outback has developed the steering rattle, while my 2015 Legacy has not. YMMV.

I think that's correct. You could open it up to be sure. Also, the FSM has diagrams showing the physical layout of the car's wiring harnesses, including the approximate location of grounding blocks. Nope. He said it's on the driver's side, near the battery.

Bingo! FWIW, the installation instructions for my Chamberlain garage door opener specifically caution NOT to use an LED bulb, for just the reason you experienced. Apparently, the driver circuitry in some LED lamps generate lots of electrical noise at radio frequencies ... and the bulbs in most garage door openers are within inches of the receiving antennas.

You can download a legal copy of the Factory Service Manual, which contains detailed and complete wiring schematics, and a whole lot more directly from the Subaru Technical Information System (STIS) web site: https://techinfo.subaru.com. The last time I checked, cost was still only $35 for 72 hours full download access.

"Half a block away" is an unrealistic expectation for Homelink; it's not designed to work at those distances. Most likely, something has recently been installed by one of your neighbors that is a source of (permissible) electrical interference in the shared, and often crowded, frequency band assigned to Homelink. Be happy that your garage door opener works reliably from the driveway.

Do you see "timing chain" mentioned anywhere in the Subaru Schedule of Inspection and Maintenance Services for your 2015 Legacy? Your answer is there. You can also consult the 2015 Legacy/Outback Factory Service Manual for additional information.