Iltl32

2013 Legacy base model. Right now I only have 1 key and so I want to get another. I have read instructions on how to program a new key fob, but how about an actual key? Is that an option? I don't have $300 to pay the dealer right now. Was hoping to buy a key online, have a locksmith cut it, and program it myself like I've been able to do with other cars. Any ideas? Thanks! Sent from my SM-G991U using Tapatalk

07 Legacy Limited 2.5i, non-turbo. I have a new ignition coil sitting on my table. I plan to do the coil and plugs tomorrow to try and resolve a miss-fire. How can I test this coil to make sure it's good before it goes in? I don't want to install it and then find out it's no good. I'm thinking I test the resistance with my multimeter? Just not sure which numbers I'm looking for. Right now I get 10.72 Ohms when checking across the leads. Thanks!

I have an 07 legacy limited with 140K miles on it. Lately it's been running weird when it gets wet; a stutter on acceleration, which cleared up once it warmed up. Yesterday in the rain it finally threw the transmission temp light and error codes relating to the transmission. I'm wondering if there's just a connector somewhere getting wet? Any ideas on whether that might be the issue, and if so on the location? Error codes are: P0700 P0770 P0731 Thanks! Sent from my SM-G991U using Tapatalk

Second issue of the day. Changing out the rear hub assemblies. Got the 32mm axle nut off, removed the ABS sensor and the 4 bolts holding the hub assembly on, but no matter how hard I pull in the assembly, the axle just comes out with it. It's stuck in there. Can I hammer the axle back in by the post where the nut goes it what? In this video at 6:11 he says to make sure the axle pushes in. What did that mean? My axle doesnt budge from the bearing. Video of my issue on imgur: https://imgur.com/a/WWKxn9z Thanks! Sent from my SM-G991U using Tapatalk

Nevermind, got it by holding a crowbar between the studs. Sent from my SM-G991U using Tapatalk

This bolt. The 32mm that girls the hub to the axle. It'd not a matter of rust, the issue is that the axle spins with the nut so there's no way to torque the nut. Sent from my SM-G991U using Tapatalk

Watched a few videos and they all just say remove the nut. The axle spins freely with the nut though. What am I missing? Sent from my SM-G991U using Tapatalk

He didn't mention a short. My thing is that since replacing the sensor fixes the issue for a year or two, wouldn't that mean it's the sensor itself? I replaced the sensor and the issue is gone again, for now. The old sensor came out with soft powdery black carbon on it, after 2 years and about 20K miles. That's more or less normal right? One thing I forgot about is that I did have an exhaust leak which I had repaired about 6 months ago, and I know exhaust issues can ruin sensors. I wonder if that was a factor.

I had to have the head gaskets replaced around 80K miles.

Denso! Sent from my SM-G991U using Tapatalk

'07 Legacy Limited 2.5i, non-turbo, 140K miles. Since 2011, I have replaced an O2 sensor 5 times. Each time, it's due to CEL and error code P0131. These sensors are supposed to last 100K miles. I drive about 10-12K miles per year. Replacing the sensor does resolve the problem for a year or two (lately more like just a year), but it seems like maybe there's another issue somewhere. Any ideas? The car is properly maintained otherwise, no other CELs, no known oil/exhaust leaks. The sensors aren't coming out filthy or anything. My mechanic told me to just replace the sensor.

With all the cell phones doing away with the aux port, I'd like to add Bluetooth to my 07 Legacy Limited. I know there are aftermarket Bluetooth receivers but they need to be charged and turned off/on with the car. I just want something native. Is there a part number for my car's radio but with Bluetooth?

I have an '07 Legacy Limited. On the rear driver's side, the cable which connects the exterior door handle to the latch has stretched out (the handle itself broke in the past and in replacing it I stretched the cable), and no longer works reliably. So my questions are: 1. Am I able to just replace this cable? I don't see a way to disassemble the latch assembly to replace it on that end. 2. If I can't replace just the cable, do I buy a whole new assembly? It looks like the cable for interior lock is also not removable, so I would need the handle attached as well, unless I'm missing something there, and I don't see anyone selling an assembly with the interior handle attached. 3. Does anybody have a part number for the cable/assembly/whatever I need to buy to fix this? Thanks!

Looking for exhaust replacement (I don't care about sound or performance boost, mine is just rusted out) and all the listings seem to only mention GT models. Are they not compatible? It's an 07 limited. Sent from my SM-G973U using Tapatalk

Do you know if this will this fit a non-turbo legacy 2.5i? Hard to get a good answer on that. Sent from my SM-G973U using Tapatalk