Jump to content
LegacyGT.com

Fabsx

Members
  • Posts

    230
  • Joined

Personal Information

  • Location
    Lehigh Valley, PA
  • Car
    '10 Legacy Gt, '05 Legacy Gt
  • Occupation
    FT Student, FT SA

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Fabsx's Achievements

Community Regular

Community Regular (8/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Check your dust plates behind rotors Occasionally during brakes or swapping wheels, they can get knock into the rotor causing such said noises. Sent from my iPhone using Tapatalk
  2. I always took the solid color as positive and whatever the other color is with a strip color as negative. I always tested the speakers before finalizing installation Sent from my iPhone using Tapatalk
  3. Leaning towards possibly the coupling that goes from tmic to throttle body. What is your vacuum at idle/or boost from AP without AC on fully warmed up? Sent from my iPhone using Tapatalk
  4. Count me in 500whp lol Sent from my iPhone using Tapatalk
  5. And I copied quote from your post “If I were him, after ruling out any visible wire damage, I would have someone press the accelerator with the engine running while flexing” ^^^^^^^^^^^ Stated running But whatever, here to help anyways. Sent from my iPhone using Tapatalk
  6. Lasfit LS plus series H7 72w bulbs Best one yet and I’ve went through a few brands to find the best. Coming from using 55w hids which could be hard to compare. Lasfit beats them. Sent from my iPhone using Tapatalk
  7. I would absolutely not run the vehicle doing this! Lol It’s a maf based system, opening up the intake tract, while running will cause bigger issues. I clearly stated the same thing you stated but with the engine running. But what do I know anyways right? Sent from my iPhone using Tapatalk
  8. I’ve seen and heard of aftermarket throttle body causing issues. Maybe pop off intake, car on but not running and have someone push the throttle pedal to the floor and verify that the actual throttle plate is opening 100% with 100% input at pedal. Just this week, had someone with a MAF code and ended up being a little fuzz inside the MAF sensor, blew it out and ran perfectly. Sent from my iPhone using Tapatalk
  9. Throttle Position sensor seems to be correlation with p0123, is the new TB Oem or aftermarket? P0102 for Maf is interesting.. remove your Maf sensor from intake and verify there is nothing inside near the wires. Occasionally a hair or bug can get stuck inside the Maf sensor causing issues. Sent from my iPhone using Tapatalk
  10. Get some good heat in there, the caliper bracket and heat that up vs the slider itself. It’ll heat up enough to where you can twist the slider out. If you’re careful enough, you can reuse the sliders and get rid of the rubber inside. I just normally pack it with grease. But to make it permanent, get new sliders, clean out the bracket inside with a wire brush to remove rust and your set. Sent from my iPhone using Tapatalk
  11. If you can move the calipers piston in, your good If the slider pins are stuck, they wont move in and out of the caliper bracket. Typically it’s the one with the rubber boot end. Edit; given your mileage and if your going to diagnose the brakes. Flush/bleed the brakes with new fluid to justify being near the brakes again. Crack the bleeders open while to verify each caliper isn’t seized. I have issues with the slider pins seizing and sticking causing abnormal wear. I just went with brembos after that since they dont have sliders Sent from my iPhone using Tapatalk
  12. Worth checking.. something people oversight. Check your brakes. They could be sticking, seized caliper or slide pins. Sent from my iPhone using Tapatalk
  13. Check fender liner What did you remove? I would jack it up, remove wheel, have someone turn the wheel, or turn it by hand with keys in acc mode to unlock wheel. That should help you narrow down to noise Sent from my iPhone using Tapatalk
  14. 1.7” piston Or 43.18mm Sent from my iPhone using Tapatalk
  15. I’ve seen those coating come off after some mileage. I normally use a credit/bendable card as a spacer with no issues between all the guides. Sent from my iPhone using Tapatalk
×
×
  • Create New...

Important Information

Terms of Use