Koyorad/Mishimoto rad's from GT fit/install it to H6

Hello

 

I would like to install in my Outback H6 MY'08 Raptor SC bigger rad- Koyorad or Mishimoto,but there is no for H6 it is only for GT,

 

if anyone has done before,please help with some info.

 

Best Regards

http://forum.liberty.asn.au/viewtopic.php?f=65&t=17494

http://forum.liberty.asn.au/viewtopic.php?f=65&t=17494

 

 

look,who gives that idea

 

http://forum.liberty.asn.au/viewtopic.php?f=16&t=17490

 

i've already start to make it

Edited July 21, 2012 by valadares

completely finished modifying and installation of MISHOMOTO H6 STI radiator.

i searched so much and there is nothing(on internet) of this modifying

nice looking setup !!

Is some sort of inline reducer necessary for the radiator hoses? The inlet/outlets on the Mishimoto appear to be much smaller than the hoses - are the hoses squeezed so as to reduce their diameter due to the wrong sized fittings on the radiator?

Is some sort of inline reducer necessary for the radiator hoses? The inlet/outlets on the Mishimoto appear to be much smaller than the hoses - are the hoses squeezed so as to reduce their diameter due to the wrong sized fittings on the radiator?

 

 

it was with only one intake 38.5mm(witch i reduce it to 28.5mm) at STI'08,and i made 2 intakes with 28.5mm-same places and diameter like original radiator for H6.i used other brackets not the original,because the original not stuffing well.

 

i did not understand what i wrong it?

Edited July 28, 2012 by valadares

I'm just doing the same, thanks to @valadares for the idea.

I'll post you pictures later.

Hi.

Can you tell us the exact rad model?

Do you had to make some mods (fix, hoses) to match your car?

I have to check on my car (2007 3.0R Spec B 5EAT) but i think it can't match, my car have 2 thermo instead of 1 for my last 2004 3.0R Spec B 6MT.

Kobemotorsports radiator seems to come soon...

https://www.kobemotorsport.shop/post/r-d-subaru-liberty-outback-gen-iv-h6-3-0l-ez30-aluminium-radiator

They answered me:

"At the moment we don’t have a ETA, but we are hoping before the mid year. We will keep our Facebook page and website updated with progress."

Hi,

 

So mine is installed !

 

 

There are a lot of modifications that need to be made for it to fit properly.

 

 

First of all, order a STI08+ Mishimoto (for example this one https://www.ebay.co.uk/itm/402040571697).

Of course you'll need to replace the 38mm intake by 2 intakes of 28mm.

 

 

http://meloman.ch/leg30/IMG-20211231-WA0003.jpg

 

After that, an adaptation of the fans is necessary, not only at the top as on the pictures of Valadares, but also at the bottom so that the fans are as close as possible to the radiator and so that they do not touch the engine once all is in place.

 

 

1. The fan support should be fixed behind the mishimoto's thread, in order to gain a few millimeters.

 

 

http://meloman.ch/leg30/fixation-1.jpg

 

 

2. You have to cut a part of the fans at the bottom so that it fits. This way the fans will be placed against the radiator, both at the top and at the bottom.

 

 

http://meloman.ch/leg30/IMG_20220125_1035336_1.jpg

 

 

Finally, you will need to cut the hoses 1.5 - 2.0 cm at the radiator side.

 

 

 

 

Here are some photos and videos to help you see for yourself what work awaits you :

http://meloman.ch/leg30

 

Especially this video which shows the entire finished work :

http://meloman.ch/leg30/MOV_20220125_1135314.mp4

 

 

And this video shows all fits and not touching engine :

http://meloman.ch/leg30/MOV_20220125_1147259.mp4

 

 

 

 

Hop it will help some of you.

Have fun.

Edited January 31, 2022 by meloman
adding some links

Thanks!

I think I'll wait for the Kobe one... [emoji23][emoji849][emoji16]

 

Envoyé de mon XQ-AT51 en utilisant Tapatalk

Kobe have hoses too.

But no shipping to France...

https://www.kobemotorsport.shop/product-page/subaru-liberty-outback-h6-my04-09