Tomcat Posted October 8, 2012 Share Posted October 8, 2012 Just simple question... are there any AT transmission suppliers for my needs?? I know Rigoli have some options years ago, but on my taste they are bit too race. How about markets in these days?? Electronic shift option would be nice and flappy pedals to steering wheel too... Tranny must handle least 600hp / 550ft/lbs Link to comment Share on other sites More sharing options...
whitetiger Posted October 8, 2012 Share Posted October 8, 2012 IPT comes to mind. http://www.importperformancetrans.com/catalog/subaru-performance-automatic-transmissions-torque-converters-and-transmission-parts.-60-1.html Link to comment Share on other sites More sharing options...
Berzerklo Posted October 8, 2012 Share Posted October 8, 2012 A 600HP automatic daily driver? Is this for a Subaru?!? Link to comment Share on other sites More sharing options...
Tomcat Posted October 8, 2012 Author Share Posted October 8, 2012 A 600HP automatic daily driver? Is this for a Subaru?!? Yeah... Now 1.5Bar boost 545hp/712nm ( 2.5L ) New strong short block 2.35L are coming and then we gona take 1.5bar with sport and 2.0bar with sharp sport http://www.saunalahti.fi/boiv/Sekalaiset/Cosworth%20engine.jpg Link to comment Share on other sites More sharing options...
fishbone Posted October 9, 2012 Share Posted October 9, 2012 Before you go further, have you considered picking up a MT Legacy, say a 2009 6MT Spec.B? The reason I ask is that although what you ask for is doable, the options of strengthening the AT are much more limited than what you can get with a MT. You gotta think about the rest of the drivetrain too. Rear and front diff. You can do all sorts of swaps on a MT, not so much on AT. Link to comment Share on other sites More sharing options...
Tomcat Posted October 9, 2012 Author Share Posted October 9, 2012 Yeah I know... Well this AT goes to my next project. Sleeper Fore. ( Stock look with beast heart ) http://www.goodhousekeeping.com/cm/goodhousekeeping/images/uS/subaru-forester-mdn.jpg We buy wrecked STi and swap all to this granny forester... = +600hp smoker It would be nice to smoke almost all you faced in lights :lol: Link to comment Share on other sites More sharing options...
RabidWombat Posted October 9, 2012 Share Posted October 9, 2012 Make sure you talk to ClimberD and frankster, they are the resident 5EAT experts. Hexmods F1 valve body, upgraded center differential would be the starting point. You're in pretty uncharted territory for a 5EAT though, so you may be replacing a lot. Link to comment Share on other sites More sharing options...
lieutenantcolumbo Posted October 9, 2012 Share Posted October 9, 2012 Might want to pm frkkevin. He is probably pushing the most whp for an auto. He was going to run his car in the Texas mile. He had IPT build his tranny, but ended up having to get a ClimberD valve body as well when it started slipping. Another poster seemed to indicate that IPT was now using a TransGo like kit in their VB now too (instead of the $0.50 spring they used to charge $769 for ), so maybe their builds are a little better now. http://legacygt.com/forums/showthread.php/dyno-vid-177909.html?t=177909 Link to comment Share on other sites More sharing options...
underground000 Posted October 9, 2012 Share Posted October 9, 2012 +1 for shaving down the pistons in the clutch pack to add more steel/clutch for each gear:) I think ipt did something like that for 4th gear an one other 5eat downshift rev match:) Powder coated wheels: completed:) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.