SSpeed Posted November 5, 2010 Share Posted November 5, 2010 Like everyone's stock LCA bushings, mine are torn to shreds... Under braking though my car is rock solid, and the steering input is still very responsive... Still, I look under at them and think those big tears can't be good for overall suspension responsiveness and stability... Searching around this forum I found this Subaru bulletin: 2005~06my legacy Front lower control arm bushings Dealers have reported, and in some cases replaced, the Front Lower Control Arms for cracked bushings. Generally, replacement is not necessary. Even with cracks up to 15mm across the outside surface, and all the way through the bushing from one side to the other, the bushing performance is still 20 times the strength of specification. This type of bushing works with compressed rubber and when the control arm travels through its full stroke it stretches a small portion of the bushing and will exhibit a crack or split. This does not affect the performance of the bushing and will not continue to spread to the rest of the bushing. It does not cause body vibrations, noises, or braking issues. A Service Bulletin will be released outlining the above information. See image to the right. The portion I question is "when the control arm travels through its full stroke it stretches a small portion of the bushing and will exhibit a crack or split" if that is indeed true, then poly bushings will get stressed under the full stroke of the control arm and perhaps fail more catastrophically eventually... That's not saying I buy that, but for those who have replaced LCA bushings with poly ones, how long have they lasted and have you seen any problems? Link to comment Share on other sites More sharing options...
grmorrow04 Posted November 5, 2010 Share Posted November 5, 2010 Poly is a tougher material. With that said, the poly bushings on the market are "solid" in the bushing, there are no slots for tears to propogate. Link to comment Share on other sites More sharing options...
BoozeRS05 Posted November 5, 2010 Share Posted November 5, 2010 Yeah, poly bushings don't flex/stretch like the OEM rubber bushing and are infinately more durable. EB's Subaru journal - 2005 LegacyGT Wagon & 2014 Forester FB25 (2008 specB - RIP) IG@legacygtliving Link to comment Share on other sites More sharing options...
Th3Franz Posted November 6, 2010 Share Posted November 6, 2010 I inspect mine regularly when I'm doing brake swaps or changing wheels. They are holding up just fine. I run the SuperPro set. This article describes how they work and clears up some misconceptions: http://autospeed.com/cms/title_Custom-Bushes/A_2833/article.html It's funny that Subaru says: "It does not cause body vibrations, noises, or braking issues." because in our experience, worn LCAs do cause all of those! When I swapped mine all of those went away, everything else constant. -Franz The end of a Legacy http://www.youtube.com/th3franz Link to comment Share on other sites More sharing options...
SSpeed Posted November 7, 2010 Author Share Posted November 7, 2010 Thanks for that, that was a really good article... Link to comment Share on other sites More sharing options...
AZP Installs Posted November 7, 2010 Share Posted November 7, 2010 No problems seen on both the AVO and the Whiteline LCA Bushings we've installed. Some have as many as 50-60k miles on them. -mike Link to comment Share on other sites More sharing options...
caramall2 Posted November 11, 2010 Share Posted November 11, 2010 While we're on the subject: - What's a good lube to use for LCA bushings (can you use somethign like Moble Synthetic grease?) that doesn't hurt the urethane? How often should you do this and what should you take apart to lube it (the inner metal insert/sleeve? (I think there's one))? - I have whitelines and really like them. My whole set up is quite a bit stiffer than stock, so didn't notice much noise/vib issues on install. Thanks. Link to comment Share on other sites More sharing options...
SSpeed Posted November 11, 2010 Author Share Posted November 11, 2010 Whiteline doesn't have any 0deg bushings right? I've been looking and can't find any, the standard says 0.5deg. I had ordered up the AVOs, but I guess they're on back order. I'm replacing the struts next week and I know I'm going to notice a lot more wobble from my torn LCA bushing once the other stuff is firmed up. Link to comment Share on other sites More sharing options...
AZP Installs Posted November 12, 2010 Share Posted November 12, 2010 The Whitelines can be set from 0 deg up to .5 deg, depending on how you place it when you press it in. As for lubing, I have had mine in for about 3 years and haven't lubed them yet. No deterioration. -mike Link to comment Share on other sites More sharing options...
Alekss Posted November 13, 2010 Share Posted November 13, 2010 if poly bushing dont flex, and stock bushings do...what are the advantages/disadvantages of them not flexing? firmer ride? Link to comment Share on other sites More sharing options...
BAC5.2 Posted November 13, 2010 Share Posted November 13, 2010 Less deflection. That means that the suspension works as it is supposed to. Energy is absorbed by the strut, rather than by deflecting bushings. This all provides better control of wheel motion, which provides more predictable and stable handling. As for a firmer ride, that is inherent of stiffer bushings and such. [URL="http://legacygt.com/forums/showthread.php/proper-flip-key-interesti-159894.html"]Flip Key Development Thread[/URL] "Genius may have its limitations, but stupidity is not thus handicapped." - E. Hubbard Link to comment Share on other sites More sharing options...
malimx6 Posted March 20, 2012 Share Posted March 20, 2012 Can anyone tell me if .5 degree offset Whiteline LCA bushings are recommended for stock suspension? I don't want any problems afterwards and I definitely don't want wheels to be moved in wheel well. Thanks Link to comment Share on other sites More sharing options...
malimx6 Posted March 20, 2012 Share Posted March 20, 2012 Also should i replace just rear LCA bushing or both? Or should i ask, is it recommended to replace just rear or both bushings? Thank you!! Link to comment Share on other sites More sharing options...
AZP Installs Posted March 20, 2012 Share Posted March 20, 2012 The caster doesnt move the wheel in or out. It rotates it froward or back. We have installed plenty of them on stok soccer mom legacies without any long term issues except amiles ontheir faces. We usually bundle the inner bushings and the rear of the front lca bushings together. -mike http://www.pbase.com/paisan/image/91072632.jpghttp://www.pbase.com/paisan/image/141039922.jpg http://www.pbase.com/paisan/image/133406601.jpg http://upload.pbase.com/image/137566671.jpg 11+ Years Maintaining, Modifying and Educating TriState Subaru Enthusiasts. Call directly as We carry almost every manufacturer now, so before you buy parts call us. AIM: AZP Installs | E-mail: sales@azpinstalls.com | 725 Fairfield Ave | Kenilworth, NJ 07033 | 908.248.AZP1 (2971) | T-1 Certified Amsoil Direct Jobber "Race Tested, Enthusiast Approved!" Link to comment Share on other sites More sharing options...
LOVEMYSUBE Posted March 20, 2012 Share Posted March 20, 2012 Hi Mike. Are those soccer mom Legacies on stock suspensions? I have the AVO offset ones and thinking replacing them with the 08 sti/spec B bushings. After almost two years, I don't think I'll get used to the extra NHV or I'm just getting old:redface: Link to comment Share on other sites More sharing options...
AZP Installs Posted March 20, 2012 Share Posted March 20, 2012 Hi Mike. Are those soccer mom Legacies on stock suspensions? I have the AVO offset ones and thinking replacing them with the 08 sti/spec B bushings. After almost two years, I don't think I'll get used to the extra NHV or I'm just getting old:redface: Yes, hence why i said they were soccer moms. just stock legacies who had bad lca bushings. We put in the whitelines and they love em. -mike http://www.pbase.com/paisan/image/91072632.jpghttp://www.pbase.com/paisan/image/141039922.jpg http://www.pbase.com/paisan/image/133406601.jpg http://upload.pbase.com/image/137566671.jpg 11+ Years Maintaining, Modifying and Educating TriState Subaru Enthusiasts. Call directly as We carry almost every manufacturer now, so before you buy parts call us. AIM: AZP Installs | E-mail: sales@azpinstalls.com | 725 Fairfield Ave | Kenilworth, NJ 07033 | 908.248.AZP1 (2971) | T-1 Certified Amsoil Direct Jobber "Race Tested, Enthusiast Approved!" Link to comment Share on other sites More sharing options...
AZP Installs Posted March 20, 2012 Share Posted March 20, 2012 Hi Mike. Are those soccer mom Legacies on stock suspensions? I have the AVO offset ones and thinking replacing them with the 08 sti/spec B bushings. After almost two years, I don't think I'll get used to the extra NHV or I'm just getting old:redface: Perhaps there is something else causing he roughness? -mike http://www.pbase.com/paisan/image/91072632.jpghttp://www.pbase.com/paisan/image/141039922.jpg http://www.pbase.com/paisan/image/133406601.jpg http://upload.pbase.com/image/137566671.jpg 11+ Years Maintaining, Modifying and Educating TriState Subaru Enthusiasts. Call directly as We carry almost every manufacturer now, so before you buy parts call us. AIM: AZP Installs | E-mail: sales@azpinstalls.com | 725 Fairfield Ave | Kenilworth, NJ 07033 | 908.248.AZP1 (2971) | T-1 Certified Amsoil Direct Jobber "Race Tested, Enthusiast Approved!" Link to comment Share on other sites More sharing options...
LOVEMYSUBE Posted March 20, 2012 Share Posted March 20, 2012 It's mostly the crappy road around here. Link to comment Share on other sites More sharing options...
malimx6 Posted March 22, 2012 Share Posted March 22, 2012 well that's what i'm trying to avoid, any wheel movement, front back or in out. I want it to look like they way it is stock. Any other bushings available to avoid this but are better then OEM (stock)? Link to comment Share on other sites More sharing options...
AZP Installs Posted March 22, 2012 Share Posted March 22, 2012 well that's what i'm trying to avoid, any wheel movement, front back or in out. I want it to look like they way it is stock. Any other bushings available to avoid this but are better then OEM (stock)? The front/back change is almost inpercievable in terms of visal appearance. The Whiteline kit is adjustable so it can be set to stock caster. We sell the Whiteline KCA334 for $130. -mike http://www.pbase.com/paisan/image/91072632.jpghttp://www.pbase.com/paisan/image/141039922.jpg http://www.pbase.com/paisan/image/133406601.jpg http://upload.pbase.com/image/137566671.jpg 11+ Years Maintaining, Modifying and Educating TriState Subaru Enthusiasts. Call directly as We carry almost every manufacturer now, so before you buy parts call us. AIM: AZP Installs | E-mail: sales@azpinstalls.com | 725 Fairfield Ave | Kenilworth, NJ 07033 | 908.248.AZP1 (2971) | T-1 Certified Amsoil Direct Jobber "Race Tested, Enthusiast Approved!" Link to comment Share on other sites More sharing options...
malimx6 Posted March 22, 2012 Share Posted March 22, 2012 Thank you for your reply. Who should be adjusting this? my mechanic that will install bushings or techs that do alignment? Are there any instructions enclosed with these bushings that show how to set the caster at 0 and .5? Link to comment Share on other sites More sharing options...
iNVAR Posted March 22, 2012 Share Posted March 22, 2012 The caster needs to be adjusted while the alignment is being done. The bushing has these little inserts/sleeves that can be turned by inserting a punch thing into the holes in the sleeve and rotating the sleeve. All the shop has to do is lossen the bolt, and rotate the sleeve and watch the caster change, and retighten once it's where you want it to be. And as mike said, the visual difference is very, very, very minor. You have to be looking for it to notice the very slight difference in wheel position in the well. Link to comment Share on other sites More sharing options...
malimx6 Posted March 22, 2012 Share Posted March 22, 2012 Thank you for your reply...now what's confusing me is that, why would there be ANY difference if caster is set to 0? Link to comment Share on other sites More sharing options...
iNVAR Posted March 22, 2012 Share Posted March 22, 2012 More details about adjustment here: http://www.iwsti.com/forums/gr-suspension-handling-stiffening/137600-what-tool-adjust-whiteline-alk-kca334.html The shop might have a "pin spanner wrench" but if they don't, someone mentioned a punch and a hammer, and you insert the punch and tap it sideways to rotate. That's what my shop did. Link to comment Share on other sites More sharing options...
iNVAR Posted March 22, 2012 Share Posted March 22, 2012 Thank you for your reply...now what's confusing me is that, why would there be ANY difference if caster is set to 0?At 0 additional caster, there's no difference from stock. But this allows you to *add* an additional 0.5 degrees on top of stock, which brought my total caster to 6.5 degrees I believe. That's what I opted for. I really suggest you add the extra caster if you buy this kit. Seems like a waste to me for you to have it set to stock. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.