Spec-B GT Posted December 18, 2007 Share Posted December 18, 2007 I have searched for this mod and I know I am a little late however, does anyone know how to do the 02 cel resistor mod? What wires do I bridge? There is no sticky in the DIY performance thread. Link to comment Share on other sites More sharing options...
DoubleM Posted December 19, 2007 Share Posted December 19, 2007 get a 2.2k ohm resistor from radioshack and solder it into the sensor wire, I hacked off the actual sensor. I think i have a picture of how It was wired up somewhere... Link to comment Share on other sites More sharing options...
XLeezardx Posted December 19, 2007 Share Posted December 19, 2007 why would u do this mod? Cant you disable the CEL with an accessport? Link to comment Share on other sites More sharing options...
twisted Posted December 19, 2007 Share Posted December 19, 2007 The AP disables the CEL But if were to say not be using the AP, then this is the alternative. Link to comment Share on other sites More sharing options...
XLeezardx Posted December 19, 2007 Share Posted December 19, 2007 damn, I have the resister mod and CEL disabled through opensource lol. Link to comment Share on other sites More sharing options...
mickeyd2005 Posted December 19, 2007 Share Posted December 19, 2007 You don't have to solder. Unplug the sensor at the harness. Bend the resistor into a U-shape and plug it into the harness. Then wrap it with electrical tape. Link to comment Share on other sites More sharing options...
Infamous1 Posted December 19, 2007 Share Posted December 19, 2007 ^^^ Exactly...please don't go and hack up your sensor for no reason. Link to comment Share on other sites More sharing options...
Impulse Posted December 19, 2007 Share Posted December 19, 2007 wait, O2 sensor? or EGT? EGT is the 2.2kohm resistor, O2 i havent figured out... i would like some information on that too Link to comment Share on other sites More sharing options...
LGT Dave Posted December 19, 2007 Share Posted December 19, 2007 wait, O2 sensor? or EGT? EGT is the 2.2kohm resistor, O2 i havent figured out... i would like some information on that too Yes, to be clear, the resistor mod is for the EGT sensor in the UP not the O2 sensor in the DP. I don't think I've heard of a mod for the O2 sensor in the DP other than the spark plug defouler trick. Link to comment Share on other sites More sharing options...
Spec-B GT Posted December 20, 2007 Author Share Posted December 20, 2007 ok I appologize for not being clear but its the o2 in the DP. After reading all of your feed back i have decided to just get a bung extender for the o2 in the DP. Link to comment Share on other sites More sharing options...
sexylegacy Posted December 20, 2007 Share Posted December 20, 2007 Just go to a parts store and buy a spark plug anti-fouler and drill the end out of it. That's all you need. Link to comment Share on other sites More sharing options...
FJuan Posted December 20, 2007 Share Posted December 20, 2007 Here's a great write up on how to do the spark plug anti-foulers. I hate to link it to the the Evo forum, but this guy did a great walkthru. http://forums.evolutionm.net/showthread.php?t=114931 My wife's balls are delicious. Link to comment Share on other sites More sharing options...
Spec-B GT Posted December 21, 2007 Author Share Posted December 21, 2007 thanks again. will be doing this on saturday to get this darn check light off for good. Link to comment Share on other sites More sharing options...
Legend Posted December 27, 2007 Share Posted December 27, 2007 Is this for P0546? My '05 LGT My '07 Supercharged Shelby Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.