Jump to content
LegacyGT.com

CDN 2.5i

Mega Users
  • Posts

    872
  • Joined

3 Followers

About CDN 2.5i

  • Birthday 05/19/1970

Personal Information

  • Location
    Kanata, Ontario
  • Car
    2005 OBP 2.5i 5MT Wagon
  • Interests
    Cycling (Road, Track, MTB)

CDN 2.5i's Achievements

Experienced

Experienced (11/14)

  • First Post
  • Collaborator
  • Posting Machine Rare
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Very happy with it. If you don't have a hitch yet, I'd recommend going 2" over the 1 1/4". The 2" model will just be that more robust. The 1 1/4" Holdup is rated for max 2 bikes, at 60lbs each. I run 3 trays on a custom setup but none of the bikes loaded weigh more than 30 each. The Yakima racks come with a threaded hitch pin that allows you to cinch down the rack in the receiver - this greatly minimizes any side to side motion. If you're looking to purchase, I'd recommend a 2013 model over the 2012 as it has added adjustability to offset the two bikes for clearance at handlebar/seat overlap.
  2. If that's in reference to my pics, Yakima crossbars on EZ Rider mounts (discontinued) and a Yakima Holdup. The pics a few posts earlier included Yakima Boa fork mounts. I don't normally run the fork mounts, opting to run the hitch rack instead most of the time. The fork mounts were just for the show
  3. hey Claw, it's not full side view, but best I have for now, as taken by Onion River Sports the day I picked up the box.
  4. Crosspost from the OBP and wagon threads: Yakima SkyBox Pro 16 in Onyx, debadged. Yakima crossbars on EZ Rider mounts Yakima Boa fork mounts
  5. Yes, you have the headers we believe were only used in early 2005 or late 2004 on some cars, perhaps early rendition of PZEV? There aren't many cars with this setup around afaik and I don't think you can run any of the aftermarket headers out of the box. The RalliSport piece won't bolt up either. I'm not sure, but you might be able to run the borla replica header you have plus a 2.5RS catted midpipe, like the Stromung or RalliSport midpipes: http://rallisportracing.com/images/100_0787.jpg It would be best to get ahold of someone with the standard '05 catted midpipe to see if it'll work on your car before purchasing one. Not sure what you'd need to do for O2 sensors and the like etc. No simple solution basically...
  6. hey Dubz, can you humor us and post pics of the manifold on your car now? Yah, will capture some drive-by's next time.
  7. If you're asking me, N.sane listed 4 vids of my car in the first post of this thread. I should take a new vid soon now that I have two resonators in the midpipe - removed the original cxlighting bottle style and now have a Vibrant and Magnaflow. Significantly less drone now...
  8. Are you sure? Did you look at the other link I posted? That 2005 has these headers: http://legacygt.com/forums/attachment.php?attachmentid=151249&stc=1&thumb=1&d=1368216114 http://legacygt.com/forums/attachment.php?attachmentid=151250&stc=1&thumb=1&d=1368216114 http://legacygt.com/forums/attachment.php?attachmentid=151251&stc=1&thumb=1&d=1368216114 http://legacygt.com/forums/attachment.php?attachmentid=151252&stc=1&thumb=1&d=1368216114 Because the headers I posted above hanging on the wall are mine, off my 2005 2.5i. And I'm running borla replicas that look just like those in the box: Here, when I took them off to get them coated after the header wrap started to deteriorate following the loss of my skidplate. http://i684.photobucket.com/albums/vv205/andrewolive/CIMG4575.jpg And cermakrome'd: http://i684.photobucket.com/albums/vv205/andrewolive/CIMG4586.jpg
  9. If yours look like pic directly above, then the header you posted in the cardbox box above should fit as a bolt on, no mods needed. Is that your header that you purchased pictured in the cardbox box above? It's not a WRX header, it's for a 2.5RS, naturally aspirated.
  10. This post has the 'other' 2005 2.5i manifold: http://legacygt.com/forums/showpost.php?p=4425745&postcount=2255
  11. I have a feeling that Dubz has that bastardized manifold - he needs to post a pic of the OE one on his car now to confirm. Needs to look like this for the Borla (replica) to bolt up. http://i684.photobucket.com/albums/vv205/andrewolive/CIMG3762.jpg
  12. Because I'm lowered on Bilsteins/Swifts, not sure how relevant a ground clearance measurement would be in my particular case. Hoping someone has actually tried it. There's a new under tray available for a good price locally right now and it's why I'm wondering if it may be worth buying it...
  13. I did create a separate thread on the topic (http://legacygt.com/forums/showthread.php/anyone-running-borlas-56410ag06e-engine-coveri-209685.html) but with zero replies, thought perhaps I should ask here, as this thread is tracked/read by most folks who have modified their 2.5i exhausts... Does anyone here have the 56410AG06E engine cover (LGT undertray) on their N/A legacy with borla headers? Does it clear?
  14. '05 is when the gen 4 car was introduced, so yes, there was an update over the 2004.
×
×
  • Create New...

Important Information

Terms of Use