Jump to content
LegacyGT.com

jsalicru

I Donated
  • Posts

    1,049
  • Joined

1 Follower

About jsalicru

  • Birthday July 16

Personal Information

  • Location
    Austin, TX
  • Car
    99 M3 Estoril/Dove

Converted

  • Aim
    RaCNG4LiFe
  • MSN
    jsalicru@hotmail.com
  • User Title
    Workaholic...

jsalicru's Achievements

Mentor

Mentor (12/14)

  • First Post
  • Collaborator
  • Posting Machine Rare
  • Conversation Starter
  • Week One Done

Recent Badges

0

Reputation

  1. Yea, sorry that I didn't really say something on here, but yes, I have now moved and settled in Austin, TX (it's actually sunny today!!) Basically there are two people that I would trust with the clientele that I had built up. Henry (socalsleeper) is one, and I have another friend down in Chula Vista named Ryan. These guys are both Porsche certified technicians. The only issue with Ryan is that although he's a brilliant mechanic, he's also quite busy. Between his startup shop (RSR Autosport) and his racing team, he tends to travel a bit. Nevertheless, if any of you guys have any questions in regards to Henry or Ryan, give me a PM or if you have my number, just call me. I'll still be available with the same phone # if you want me to consult you with anything as before. NOW I JUST NEED SOME BUSINESS FROM AUSTIN, TX AREA!!!
  2. Hey Jose,

    Not sure if you remember I have a black on black wagon you worked on a while back. Used to work at Eibach, K&N and now Yokohama, I need some springs put on again. Whats your schedule look like on for this?

     

    Scott

  3. LOL, that was funny. I think I might put that on my sig!
  4. BTW, I've heard there's this one guy that from time to time does installs out of his garage in Murrieta ;)
  5. My garage also works quite well. Im sure there are plenty here that will vouch for my work... In addition, since Im in between jobs... my schedule is EXTREMELY flexible.
  6. Added a section in regards to installing a EGT sensor. Took it out of my Defi How-to that I did for the STi guys a while back
  7. you never know, trust me, you just never know
  8. Done, added all those specs too... even the tiny BOV one
  9. This is something that comes up all the time. I get PMs from people asking for information in regards to part numbers and other aspects of exhaust part installation. So, here is a thread with all sorts of information in regards to exhaust parts. This is for all the DIY people out there... you will do a much higher quality job if you follow the specs below. Downpipe-to-catback torque spec...........13.0 ft-lbs Axle-back torque spec ..........................35.4 ft-lbs Exhaust bracket torque spec ..................26.0 ft-lbs Transmission bracket torque spec ............26.0 ft-lbs Downpipe-to-midpipe torque spec ............26.0 ft-lbs Downpipe-to-turbo torque spec .............. 26.0 ft-lbs Uppipe-to-turbo torque spec ...................26.0 ft-lbs Turbo bracket @ up-pipe torque spec .......26.0 ft-lbs Turbo bracket-to-block torque spec .........24.6 ft-lbs (highly unlikely you will need this one.) Head-to-manifold torque spec .................29.8 ft-lbs Manifold-to-crossover pipe torque spec .....26.0 ft-lbs Manifold-to-uppipe torque spec ...............26.0 ft-lbs Manifold heatshield torque spec ...............9.6 ft-lbs Front 02 sensor torque spec ...................22.1 ft-lbs Rear 02 sensor torque spec ....................15.2 ft-lbs Intercooler-to-turbo flange torque spec ....11.6 ft-lbs Intercooler brackets torque spec .............11.6 ft-lbs By-pass valve-to-intercooler torque spec .. 4.8 ft-lbs In addition, here are the part numbers for all the exhaust gaskets too. Head to Exhaust Manifold Gaskets - 2 are required to replace in case you install a header. 14038AA000 Driver's Exhaust Manifold to Crossover Pipe gasket 44022AA160 Crossover Pipe to Pass Exhaust Manifold Gasket 44011FA020 Exhaust Manifold to Uppipe Gasket 44022AA170 Uppipe to turbo Gasket 44022AA150 Turbo to Downpipe Gasket 44022AA180 Downpipe to Midpipe 44011FE000 Flex Joint Gasket (the donut) 44022AA122 If you guys want, I might also include a how-to on UP/DP installation, but frankly, those are a dime a dozen on WRX sites.. More information Installing Exhaust Gas Temperature Sensor Tools Needed: 14mm wrench (possibly 2) 14mm socket 12mm socket 1/8" NPT tap Various drill bits (11/32, small drill bit for pilot hole, big drill bit for possible hole on heatshield) Dremel (optional - for heatshield) Panel popper or flathead screw driver PB Blaster or equivalent penetrating lubricant The routing of the harness is entirely up to the end user. A good place to install the sensor is in the “button” of the driver’s side exhaust manifold. During more recent testing, it has been shown that the driver’s side of the engine runs higher EGTs than the passenger’s side. Carefully lift the front of the car and secure using jack-stands. 5. Remove belly pan. There are 3 12-mm bolts in the front and 1 in the rear. There are also 2 plastic tabs on each side of the pan, for a total of 4. There are tab removers available, but a flat head screwdriver will work if one is not available. Remove driver’s side exhaust manifold heat shield. This is secured by 3 12-mm bolts. Remove the 2 14-mm bolts in that hold the manifold to the crossover pipe. Hold on to that gasket. You will need at least one open-end wrench for this, but two are useful. Ratchet type open-end wrenches are the best. Remove the 3 14-mm nuts that hold the manifold in place. Locate the little button in between the No. 2 and No.4 exhaust pipe. Drill a pilot hole in the middle of the “button”. Drill a hole using a 11/32” drill bit. Make sure to use some type of lubricant to cool and help out the bit. Also, regulate the speed so that you can cut into the metal more efficiently. Faster really is not better here. Start to tap your thread using the 1/8” NPT tap. Get some help for this as it requires some incredible amount of force. It is typically not recommended to back out of the thread very often when using a NPT tap. And when you think you have gone far enough and hard enough, back it out, clean the threads, and go again a little harder until it REALLY is impossible. Clean the threads and the interior of the manifold to remove metal shavings. Install the fitting. Use discretion when torquing it down. If you plan on re-using the heat shield, do not install the sensor just yet. Mark the heat shield in the appropriate location and use either a HUGE bit (bigger than 3/8”) or use a dremel to obtain the desired size. Install the manifold back to the engine and crossover pipe. Do not forget the gasket! Install heat shield. Install sensor. Do not over-tighten. Plug sensor harness. When starting the car, you might experience some smoke due to the lubricant used during the drilling process. Other than that, check for leaks.
  10. well, the issue for me isn't the "Honda" sound. Its the fact that 3 spacers are too loud, 2 spacers sound wrong.
  11. Well, I will tell you guys this. It doesn't work well when you have equal length headers.
  12. Unpimp Ze Auto! Haha, actually, that statement there isn't true. You can make a manual boost controller out of plumbing parts. I did it on my FD3 RX7 (a REAL performance car)to tune the pre-spool of the secondary turbo. Worked great. Also, on some cars, you can use washers to fix the camber.
×
×
  • Create New...

Important Information

Terms of Use