Jump to content
LegacyGT.com

kzr750r1

I Donated
  • Posts

    2,114
  • Joined

1 Follower

Personal Information

  • Location
    Nor Cal
  • Car
    2006 OBXT/1998 Toyota SR5 4x4 Kingcab

Converted

  • User Title
    Doing it AGAIN!

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

kzr750r1's Achievements

Veteran

Veteran (13/14)

  • Reacting Well Rare
  • Dedicated Rare
  • First Post
  • Collaborator
  • Posting Machine Rare

Recent Badges

94

Reputation

  1. Sorry you have to open up the third level of hell to change the sensor. For good measure you should change the other cam sensor and crank sensor. Coil packs are a good measure as well. But you can make that decision later to see if the other sensor changes help. Finding leaks is good to find early. My first turbo change was a mess. In clocking the turbo (BNG 16G) after install popped the drain hose out of position. Didn't notice until there was a lake of T6 on my driveway.
  2. Great news! Take it easy on the breakin and buy your oil and filters in bulk.
  3. Ok now on the same page. You have to turn in a bunch more till all the marks will line up again because of the uneven number of teeth. http://www.youtube.com/watch?v=iCGTdaffoiA&t=291s
  4. As I recall it's the same part for the cam sensors. Can't remember right now if I replaced mine on the last rebuild. Have had them go bad or pop up a fault. Since you have an access port will clearing the codes return with the same again? When the cam sensor went out on mine the ex wife and kids were on their way back from san diego. I had to talk her thru plugging in the access port and clear codes. Ran fine after and two new cam sensors ordered before they arrived. I may have some old spares in stock will look this weekend. You mention timing it several times? I'm puzzled by this as it's not like we have a distributor to adjust.
  5. While replacing 4qt of ATF, Trans filter and four of the six hoses the Tans shop buchard with worm gear clamps found another mistake they made. Aside from the WIX filter for the ATF loop. I'm seeing a paper gasket for the trans pan where I don't see one mentioned in the manuals. We have some seepage happening. Only Three Bond 1217B mentioned. In addition there are three holes that must be filled. These are inline with the bolt holes. So I can only guess the shop used an aftermarket gasket kit. Clearly right stuff used to stuff the trans to the diff. Huge amount of squeeze out on the outside. Likely the same on the inside. So... getting time of the 1217B from the stealership soon and some more ATF to drop this pan and stick this puppy back on by the book. Also have an alternate fuel regulator setup installed. Seems to have made a difference. A bit smoother but time will tell.
  6. Yes. All depends. Some may be using a red putty like material. Or tef tape. I've been using version 1211 lately, read into it a bit more at one point. Chemical: IE Fuel resistance is a plus. Of course I want the oil to stay in as well. This last ZRX and EJ rebuild had me going down the rabbit hole for added protection. In rare occasions gravity fed carb systems can fail on the bike and fill a crankcase with gas. Had it on hand while rebuilding the EJ a year or so ago now. No leaking on either. Nice part is it's thinner and has a longer tack time. Thin, brush it on. Keep it clean and fabam. Nice seal and little blowout extra silicon running thru your AVCS hosing your operation internally.
  7. The unit I picked up from Torque Solutions has Teflon Tape on it already. But three bond would work too. Just be sure to clean the threads regardless of what you use.
  8. Take your time. Prep the tensioner vertically as described in the manual/instructions. Slowly. Last round I did it twice. Was pretty sure one pulley jumped a tooth. In the end all good.
  9. Take a look at the hard crossover line from the head to the PCV system. I've had that lined with schmoo from not driving long enough distances. Remember oil accumulates moisture as it cools. Needs 20 or more min of run time to evaporate. Just put a see through case cover on the ZRX and reminded about this every time I'm starting it up. Oil looks like a milkshake till it runs for a long time.
  10. Be careful trying to flip the stock claps over. I tried last time and ended up putting them back together how they come stock... Essentially upside down when the manifold is installed. No matter what I was doing the extended threads would bump into something or another, not optimal. Even after cutting down the screw.
  11. Should have some residual from the initial install of pistons and what not. What crossover are you talking about? One on the top is coolant. My guess is the tie to the Oil cooler you're referring to?
  12. Well finally getting back to this. Found just the inner fin that was cracked off where I had stored the old GS splitter. Probably ditched the rest thinking it would be easy to get a new unit form GS if I ever placed it back in service. Well called GS and Nope! They will not sell me one. So out of curiosity wondering if you have one last unit available to install/try/modify.
  13. Yeah I had mine off as well. Hit the main connector terminal to just reflow the solder. Still no luck and lost one of the rubber mushrooms. In the meantime ordered another cubby from fleabay to see if it would make a difference. NOPE! I can slap it back into reading by hitting the dash just above cubby. Not hard... But hard enough at one point I guess cracked my old bezel. Water under the bridge at this point since the new fleabay unit is in really good shape. Time to inspect the wires. Need to tear into it any way at some point to replace all the air actuators.
  14. Was going to take some sunset shots yesterday evening. My plans changed with the weather and road closures. Tumble weeds were blowing all over the canyon and started raining heavy just before sunset. So I just hung out at a friends and enjoyed the evening. More soon.
  15. Alignment check up tomorrow afternoon. Going to test some more for rub tonight and confirm no spacers needed. Lock to lock no issue only seen some possible rub under compression on the rear inner fender that I may live with for now. It's tight! But looks like this combo will worK as I've hoped.
×
×
  • Create New...

Important Information

Terms of Use