derkahn

Thanks for the advice... here is kinda my issue/complaint/armchair diagnoses... so as far as A/F learning,correction, FBK FLKC etc.. I have watched these , however I wish there was some sort of programming to put into a map etc to warn of this stuff.. realistically its a bit of a PITA to always have the accessport out (then put it away as not to tempt thieves) and also be watching that all the time.. I just want to get in my car and drive (insert you should have bought a higher HP stock sports car(insert car of the month) here), I think I saw a thread on NASIOC a while ago about people complaining about the cars knock sensors/system etc and how it doesn't lend it self to high performance cars..?? I don't really remember. I have been in a subaru that had knock before and really bad knock is pretty hard to not notice... Since I am the only one who drives this car I can't say that I have ever had a moment where I noticed something not right w the motor prior to this... Here's my armchair diagnoses.. maybe .. I recently read on the injector dynamics website ( I think) an article about filtering fuel (especially e-85) and how the oem system may not do an adequate job of filtering (I have seen lots of guys put an inline fuel filter in the engine bar w a servicable element/filter) and since cyl4 is so close to the turbo/up pipe etc the heat/heat cycling might shorten the service interval of that injector , especially if the fuel is not filtered adequately. I imagine a 1000cc injector running a few % points off of the others at WOT might just cascade into kablooey... totally guessing.. /frustrated.. but on a + the car still runs well at anything other than idle....? maybe the cure for ringland failure is all boost all the time.. kidding..

95% of the time I was at only 18...

Yes:(

cyl 4.. 65psi...ringland failure on a built motor w cosworth pistons....:( .. pro tune, crawford AOS, brad penn oil every 3k, lower rev limit, WTF????... I might be done... pouring $ into a depreciation asset is never smart but I just put in a new clutch/flywheel ,new TMIC, new turbo, had the ECU replaced (actually thanks subaru, they paid for 1/2 of that) .... I should just buy a merc 4wd sprinter van and put a shifter kart in the back to get my jollies off... MOTHER PUCKER!.... so put in a new motor ($6k) drive it for a year or two until the RS comes out or part this sucker out and never look back..? I know you gotta pay to play but...man..this hurts.

yes I have a V3 accessport.. are there certain parameters that I should look at to help narrow it down? newb in the datalog world.. I usually like just wrenching on things;)

uh oh... cyl4 misfire and Pfffe code...hoping it is just an injector..I haven't done anything yet.. (swap injectors, coil packs etc) but I am worried of the cascade of events even if it is "just" an injector.

I'm no expert but uh why wouldn't they be for daily use ? I had mine in for 3 yrs....daily..and not more expensive either.. I'm neutral on either rack or quickener.. The rack will feel oem, where as the quickener ( at least mine was) made the steering heavier ( which I liked) also the quickener had about 3mm of play when the wheel was straight. Annoying for the first 5 min then u forgot it was there.

Quickener changes ratio before it inputs into rack. IMO doing a quicker rack or a steering quickener is one of the funnest mods ever.

Quickener changes ratio before it inputs into rack. IMO doing a quicker rack or a steering quickener is one of the funnest mods ever.

now just add one of these and you can be 1 turn lock to lock:) http://legacygt.com/forums/showthread.php/most-enjoyable-mod-so-far-l-e-steering-quickener-126316.html?t=126316

Looks like my bnr20g is sick... New turbo is on the way . I'll let you all know what the cause was. On the bright side I got a grimmspeed tmic that with the addition of a different hose from GS I can run sti type turbos ( I think you can do the same thing w process west' new tmic too) so a Garrett gtx is in my future.

Is anyone having issues when installing the scoop with the oem hood insulation/foamy stuff? All the pics I have seen so far do not show it.

hurry up!!

every time it snows I start thinking about diffs.. and while not necessarily lgt specific I thought this might add to the conversation with lots of pictures: http://thefactoryfiveforum.com/showthread.php?13240-A-spotters-guide-to-Subaru-differentials I am still not clear on what people are doing to "improve " on a r160 diff.. can you re shim it or can I try to find a spec -b rear diff (since they are like unicorns anyway I doubt I would find one) or spend big $ and get a ppg one?

This thread is terrible...... Just when I thought.."hmm no more messing w my car just general maintenance here on out" you guys bring this up.. now it's nagging on me... cause.. it totally makes sense to do... so When you guys get it all figured out come out to colorado and help me do it, because electrical stuff is wizardry and electrical stuff going into gas tanks scares me even more.