Jump to content
LegacyGT.com

underpowerd

Mega Users
  • Posts

    973
  • Joined

2 Followers

About underpowerd

  • Birthday 01/30/1976

Personal Information

  • Location
    CC, MD
  • Car
    05 OBP LGT 5EAT UL +PE1818F/20 +HFS-6

Converted

  • User Title
    HEET Miser

underpowerd's Achievements

Mentor

Mentor (12/14)

  • First Post
  • Collaborator
  • Posting Machine Rare
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. try on some salomons. I'm still grinding through my daily worn (long discontinued) eskape gtx's -- settled on them during the vain search to find a satisfactory transition from my old lowa jannus (everything sort of duty... for years) -- turned out to be the second best shoes I've ever owned.
  2. http://www.cruisincaskets.com/_/rsrc/1372376216655/home/DSC_0049%20web.jpg the irrational mod/lgt-dependence bug will probably get something like this out of me before I bail. ...if you're like me, right after you stopped laughing at the silliness, you said to yourself: 'Is that alcantara?"
  3. been using for many years; trick for that 'suby grime' is to not rush right in and start wiping, but let it soak for about 20s after you spray it. two passes like that clears just about anything.
  4. ^if I had any kind of issue with the 'pop,' (i.e. no pop, overly easy/difficult pop, trouble fitting in pre-pop) primary focus would be compelled upon the snap ring on the end.
  5. you'll know if the breather has to go if you cant pry it off without breaking it
  6. i believe the spring you're talking about is a clip that sits in that small groove at the tip of the axle; you want that back on there. i find it best to give the axle a few rotational-type shakes when trying to slide it back in; you can feel when the splines line up, and you can begin sliding in; but there will still be some clearance between the cup and case when you finish the slide -- at that point you can just give the axle a little pop on the hub end with something blunt/dense to compress that spring clip you mentioned and fully seat the axle. it doesn't take too much force, so i typically don't worry about damaging the threads on that end before giving said gentle pop -- but protect them if you feel you may want to.
  7. if you have a PA car with big miles like that, invest the $10-15 in a diamond wedge from any home improvement store; with a decent sledge behind it, it will very likely save you much pain in knocking that lbj free vs. any conventional wedge/pry attempt. and as max said, some kind of impact and PBB are paramount. i've also reused the axle nut -- so long as you can re-crimp it. good luck.
  8. thanks frank -- bah, i didn't even think of temp sens. you're probably right -- i was hoping like hell for a fuse/capacitor. pics attached; i was referring to the red guy in the center. here's the thing: i had a fluke short of two wires (YR, Blk) of the giant harness (B21?) care of the turbo oil feed. when the two ultimately wore through enough to short, it was taking F/B#12 out instantly @ 'on' key turn iirc -- being a 20* evening, it activated my AAA card, lol. so as i see it, the #12 fuse did its job with the direct short, but it appeared that the YR wire had been exposed far longer than the black, and as i understand the pinouts this wire is a very heavy fellow with regards to the 5eat and may have seen some intermittent (-) contact, again via the oil feed which i imagine must carry some ground. i may be jumping to conclusions, but my mind can't help but to tie my long-standing P0700/740 (tcc sol) to this unfortunate sneaky situation; i just think that if it were something more mechanical like worn clutches (as some others have reported with this code), i'd have certainly seen a failure by now. i have no slipping whatsoever, and i get the sport flash on proper cue (in M2+ on slight incline @ 1/8 throttle or so [mostly M3+]) to suggest procedural vb replacement.
  9. can anybody field this one (mr. dave/frank ?)? can snap a pic if description unclear...
  10. One for the top brass: What is the task of the lone exposed diode on the VB unit (capacitor, fuse, switching, volt. reg, etc.), and what symptom(s) would one expect to encounter if fully/partially burned? TIA, gents.
  11. looks familiar -- at least you weren't jumping up and down on it when it happened like i was...or were you? 30 minutes later, i forgot the $150 i just dropped on the 1/2" impact the instant it took that nut off in < 10 seconds.
  12. when you see the inner spline end of your replacement, you'll id the 'clip' and get the idea; it simply a plain open-end ring that sits in a groove almost at the very end of the shaft. people have characterized the removal as a 'pop,' which is pretty fair; as you carefully pry, you'll feel the pop of the clip releasing, and immediately gain some clearance -- then the rest slides out like butter. the seal is seated inside; if you're deliberate and take reasonable care, you shouldn't harm it or disturb it at all during removal. as for installing your replacement, as you guide in, 'feel' your splines into alignment. then, holding that in place, give the opposite (hub) end of the axle a tap with something blunt and a bit weighty (protect the threaded end if you like). i find the clip really responds to method this as opposed to trying to force-push the axle in. best luck.
  13. finished at a relaxed pace in >2hrs today. no s/t, no lift, and only hand + electric impact. the hero? PBB & this little guy, $10 diamond wedge i had originally bought for an LBJ that looked like it belonged to the titanic (same duo helped to make very short work of that, also). http://simage1.sportsmansguide.com/adimgs/m/2/284818i_ts.jpg holding by the business end turns it into a tight quarters precision hand-sledge, hub leapt off in minutes also perfect for one-tap axle-popping into trans.
  14. Don't feel too bad, I got washed out on my first try last weekend; I know from peeking inside the threadhole of the pinch that my LBJ must be your guy's twin. I miraculously got the bolt out (some of it in the form of a tight little cloud of rust) with an electric impact, but my crowbar didn't have the girth to budge the joint more than 1/32 or so; I'll be going back in with a diamond wedge. I also made quick work of stripping the allen on the EL, and resorted to visegripping the inner washer/seat to get it back on. Add my voice to the swelling chorus that NE cars really turn this apparently straightforward DIY down a byway through some unhospitable and profanity-evoking territory.
×
×
  • Create New...

Important Information

Terms of Use