Jump to content
LegacyGT.com

jdeitz1979

Members
  • Posts

    124
  • Joined

jdeitz1979's Achievements

Collaborator

Collaborator (7/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. VF48 turbo? Stock aluminum tmic? Sent from my iPhone using Tapatalk
  2. Soo... after calling and talking to a different guy, was informed that the warranty is only for up to 100k and will expire in 2022. The guy I first talked to apparently had messed a few things up there at the service desk and the guy I had spoken to wasn’t so happy about that. He also said that Subaru should’ve covered them no matter what but gave his apologies for not being able to help. 8k is what a new trans with them installing it would be. One hell of an ouch lol. I’ve done some internet digging and found a couple repo insurance yards that part out cars that have a few trans with low mileage. Figure if I could grab the vin and run it with the Subaru service and see if it was worked on within the recall I should probably go that route Sent from my iPhone using Tapatalk
  3. Record wasn’t literally speaking, but yes agreed in writing would be best. Sent from my iPhone using Tapatalk
  4. Yea idk. That’s what the guy at Romano Subaru had told me. After vacation we’re going to take it down, but before I do I think I’m going to have him say it again so I can record him saying it lol. Sounds like from what you guys are saying he may have misspoke. Sent from my iPhone using Tapatalk
  5. It’s got 170k [emoji1787] but runs and drives fantastic, I’m the second owner of it Sent from my iPhone using Tapatalk
  6. I had contacted the Subaru dealer today and spoke with them. After running the vin number they said that it was still covered and that the warranty was good until 2022 with no mileage restriction. Should I double check with a different dealership to make sure he wasn’t smokin some crazy stuff? Sent from my iPhone using Tapatalk
  7. Oddly enough, I just slipped into the seat of a new to us 2012 legacy. It has a trans problem as well that wasn’t disclosed when buying the car from the po. At a low speed, like as your coming to a stop or pulling into a parking space it shutters, and sometimes will stall. But it has an odd noise like the original poster is talking about with the wine noise. I haven’t looked into the issue yet but was trying to pre plan by reading through here. Sent from my iPhone using Tapatalk
  8. Why not rebuild what you have? I’m sure if you caught it soon enough you could save most, maybe replace the crank and rods Sent from my iPhone using Tapatalk
  9. It’s on the right side of the solenoid. I’ll take a pic of it, directly behind the alternator, small hose, plugs in the right side. I can get some pics on here tomorrow. Sent from my iPhone using Tapatalk
  10. Still waiting for that part to come in, so I don’t really know if that does it or not yet. I guess I could have missed the “t” under the ic, I’ll look again, and also double check all of the hoses again as well. I could have easily over looked a bad spot on one of them Sent from my iPhone using Tapatalk
  11. I haven’t driven it at all. I have a Cobb tune in now, but if that’s not enough then I guess I’ll have to grab a tactrix cable. Can’t the purge solenoid cause an this code? ***edit*** Prior to my parts install, the car was running fine, and was stock. Had no codes at all. I had a leaky pcv breather hose, I tore into it to fix that hose, and that’s when I had the p0171 code, ever since then. I only drove it like ten miles, if that. I don’t drive the car much, but come spring, it would be nice to drive with some power behind it. Sent from my iPhone using Tapatalk
  12. Cleared codes after checking hoses and wiring. P0171 comes back. If hoses and wires/plugs are all in order, where else can one look to find the cause of this code Sent from my iPhone using Tapatalk
  13. Got around to putting some upgrades in my car. ‘05 LGt. Invidia up and down pipe, could air intake, vf52 turbo, and Cobb tuner. Install went well, but I did snap the nipple off the boost control solenoid, which has been Ordered just isn’t here yet. These are the p codes I’ve had since the work has been done. p0244, p0457, p0171. The only thing not fully connected at the moment is the bcs. Will this clear up those issues ? Sent from my iPhone using Tapatalk
  14. Sent from my iPhone using Tapatalk
×
×
  • Create New...

Important Information

Terms of Use