DA_MAXX

Can someone running the NU9020 provide their Hands Free Voice quality settings?

Dealer performed update from NU9017 to NU9020. Everything appeared to work. Today, noticed that when making a phone call, I can't hear the audio from the phone over the speakers, just a slow clicking sound. All other BT functions work fine, pandora, tune in radio. Tested with a Samsung and Apple phone. Same problem. Went into settings and noticed HF Voice quality settings. Mine is set to 0000. Is this the same on others? 15, Premium, w/Nav. Thanks,

The NU9017 is for 2015. NU9309 for 2016 as ammcinnis stated.

Festoon, 31mm, 3022 or DE3175, for Dome and Map.

Mark N, There's a few updates. The first 5 pages of the TSB covers them all. Here's the short list: • Mirrorlink 1.1 updates • Enable Mute function for Navigation guidance • Incomplete display of intersection names in combination meter • Increased accuracy of the XM Traffic information displayed • Intermittent delay (approximately 1 minute) in display of map information after initial start-up of Navigation function (2015MY Legacy and Outback only). VERY IMPORTANT: In addition to updates for these five conditions, each of the new files listed in the table below contain ALL of the previous updates for conditions referenced in prior TSBs 15-182-15R, 15-183-15R and 15-198-16R which this TSB replaces. An overview of conditions addressed in the three prior TSBs is provided below. You shouldn't have to take it to the dealer, twice. Just verify the versions and check the vehicle monitor before leaving. For those with Macs, I'm sure there's a *.zip file version. If not, send me a PM. Here's a list of the available files from Subaru for Legacy: Legacy & Outback: 2015MY Legacy & Outback w/ F10 NAVIGATION Update File #1 2015MY Legacy & Outback w/ F10 NAVIGATION Update File #2 2015MY Legacy & Outback w/ F10 7" DISPLAY AUDIO Update File #1 2015MY Legacy & Outback w/ F10 7" DISPLAY AUDIO Update File #2 2016MY Legacy & Outback w/ F10 NAVIGATION Update File #1 2016MY Legacy & Outback w/ F10 NAVIGATION Update File #2 2016MY Legacy & Outback w/ F10 7" DISPLAY AUDIO Update File #1 2016MY Legacy & Outback w/ F10 7" DISPLAY AUDIO Update File #2

This also happened to mine. Update #2 didn't take the first time. Check your versions for Nor, eSD, CAN, and DB.

CT2015, Securityguy has an iphone 7+ and I have a 6+. I'm running iOS 10.2. Neither of us have issues with the gps working while tethered to the HU. Have you verified the version levels after the updates?

CT2015, If you're in the Vehicle Monitor screen and the % throttle, Temp both read correctly, btw car doesn't have to be running, just press gas pedal, then it appears the update 2 did take. So might be an iPhone 7 thing. I have a 6plus.

CT2015, Does the Vehicle Customization menu work? or hangs? How about Vehicle Monitor? Neither of those 2 worked for me after the first attempt of Update #2. Once it took, all started working.

CT2015Legacy, From the TSB, for 2016 w/NAV. The file is "NU9309_USB_2nd.exe".

My files for 2015/Nav, were *.exe files. When you run them, it's self extracting files. The files are *.kwi. Update #1 had 1 file. Update #2 had 3 *.kwi files. So it should work on Mac.

I believe I got it updated. The TSB procedure isn't very clear on verifying the correct version after each update. It says to verify CAN, but what is the updated number? I had to re-apply update #2, twice. I didn't reapply update #1 before doing #2, the second time, as the TSB says. The first time I ran update #2, it was a lot faster than #1. The second time, it was much longer. So appears it took. My final versions are: Nor=NU9017, eSD=NU9017, CAN=14.0015, and DB=NU9017. Does this match others ? Vehicle customization works. Haven't tried MirrorLink.

So how long does it take to perform update #1 ? and #2 ? The TSB recommends connecting a battery keeper while doing the update. If the updates take a while, can it be done with the car running?

Solkid212, welcome to the forums. So as you can see, folks highly recommend "searching" the forums before posting your question. There's been alot of threads regarding "lights". I think some folks are sensitive to them. Regardless, What's your goal ? What are trying to achieve? I don't drive in a lot of places where I use my High Beams. I think most folks in rural areas would. If you need them, then I would suggest the LED 9005 High Beam option. I love my HID low beam H11 setup and the H11 LED Fog lights. I hardly ever use my High beams. The drawback with having 9005 High Beam LEDs is that there's no "lo" setting. They're either off or on. So I choose to just drive with my lights (lows) ON all of the time, Day or Night. It's been over a year and no issues. Btw..all my lights were from XD. Great Setup !

lscmark. So you go 6k between changes and the oil level is at the full mark ? Was it always this way for all the changes? or did it get better with more mileage ? I'm at 23k and have noticed about 1/2 quart low. Thanks,